Strata DK 16 Manual
Strata DK 16 Manual
Strata DK 16 Manual
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
INSTALLATION-PERIPHERALS<br />
SECTION 100-8<strong>16</strong>-207<br />
MARCH 1993<br />
4.23 Amplified Speaker Installation. install the<br />
HESB Amplified Speaker option in accordance<br />
with the following steps (refer to Figure 7-12):<br />
1)<br />
2)<br />
3)<br />
4)<br />
5)<br />
6)<br />
7)<br />
8)<br />
Connect a jumper between terminals 1 and 2<br />
of the HESB TBl terminal block.<br />
Connect a jumper between terminals 6 and 7<br />
of the HESB TBl terminal block.<br />
Connect a jumper between terminals 5 and 8<br />
of the HESB TBl terminal block.<br />
Connect a jumper between terminals 3 and 4<br />
of the HESB TB2 terminal block.<br />
Connect a jumper between terminals 5 and 6<br />
of the HESB TB2 terminal block.<br />
Connect the 600 ohm PAGE RCA jack output<br />
on the <strong>DK</strong>8 KSU or <strong>DK</strong><strong>16</strong> Base Unit to termi-<br />
nals 3 and 4 of the HESB TBl terminal block.<br />
Connect the power supply’s +I 2V lead to ter-<br />
minal 1 of the HESB TB2 terminal block, and<br />
connect the OV lead to terminal 2.<br />
Plug the provided power cord into the power<br />
supply and to a 117VAC, 60Hz power source.<br />
4.24 Amplified Speaker Test. Test the amplified 4.26 Talkback Amplified Speaker Test. Test the<br />
speaker installation in accordance with the follow- Talkback Amplified Speaker installation in accor-<br />
ing steps: dance with the following steps:<br />
1) Make an external page.<br />
l Page should be heard over the HESB.<br />
2) Adjust the HESB volume control to the desired<br />
level (screwdriver adjustment on back of<br />
HESB).<br />
4.25 HESB/MDFB Talkback Amplified Speaker<br />
Installation. Install the HESB/MDFB Talkback<br />
Amplified Speaker option in accordance with the<br />
following steps (refer to Figure 7-13):<br />
1) Connect a jumper between terminals 1 and 2<br />
of the HESB TBl terminal block.<br />
3) Connect a jumper between terminals 5 and 6<br />
of the HESB TB2 terminal block.<br />
NOTE:<br />
HESB connections made in steps 4 - 7 may<br />
be accomplished using the HESB VOICE and<br />
DOOR PHONE modular jack instead of the<br />
TB1 terminal block.<br />
2) Connect a jumper between terminals 3 and 4 1) Find a suitable location on the mounting sur-<br />
of the HESB TB2 terminal block. face for the HESB.<br />
7-<strong>16</strong><br />
4)<br />
5)<br />
6)<br />
7)<br />
8)<br />
9)<br />
10)<br />
1)<br />
2)<br />
Connect terminal 7 of the HESB TBI terminal<br />
block to pin Ll of the MDFB.<br />
Connect terminal 8 of the HESB TBI terminal<br />
block to pin L2 of the MDFB.<br />
Connect terminal 9 of the HESB TBl terminal<br />
block to pin 1 of the MDFB.<br />
Connect terminal 10 of the HESB TBl termi-<br />
nal block to pin 2 of the MDFB.<br />
Connect the 600 ohm PAGE RCA jack output<br />
from <strong>DK</strong>8 KSU or <strong>DK</strong><strong>16</strong> base unit to terminals<br />
3 and 4 of the HESB TBl terminal block.<br />
Connect the HACU-120 Power Supply’s +12V<br />
lead to terminal 1 of the HESB TB2 terminal<br />
block, and connect the OV lead to terminal 2.<br />
Plug the provided power cord into the power<br />
supply and to a 117 VAC, 60Hz power source.<br />
Make an external page.<br />
l Page will be heard over the HESB.<br />
Verify that someone speaking into the door<br />
phone can be heard at the paging station (with<br />
this application, pressing the door phone but-<br />
ton is not required to talkback through the door<br />
phone).<br />
4.27 HESB Wall Mounting Instructions. The<br />
HESB can be mounted to a wall or other vertical<br />
surface. Use the following instruction to mount the<br />
HESB (see Figure 7-14).