SHARP TROUBLE & ERROR CODES AR-651, AR-810 - OlsonBros

More documents

Recommendations

Info

[E5A] Trailing edge of paper not passing the exit sensor Is there any paper at the reverse section when the exit cover is opened? NO Remove the paper. Is the exit motor driving? (Perform the output check in the test mode: 03-120) YES 1. Check if the connector of the exit motor is not disconnected. 2. Check if the connector J336 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open-circuited. 4. Check if the conductor pattern on the LGC board is not short- or open- circuited. 5. Replace the LGC board. 1. Check if the setting of the paper size is correct. 2. Check if there is no abnormality and extraneous material at the guide and myler in front of the exit roller. YES NO 3. Check if there is no mechanical loading at the exit follower roller. AR-651/810 TROUBLE SHOOTING 5 - 32
5.1.5 Original jam in RADF [E71] Original feeding jam Are the pickup roller, feed roller and separation roller dirty? NO YES Clean the rollers. Is the transport force of the rollers insufficient? NO YES Replace the rollers. Is the original abnormally curled or folded? YES Flatten and set it again. [E72] Original transport jam [E73] Original discharging jam Are the registration roller, read roller and exit roller dirty? YES Clean the rollers. [E74] Original reversing jam Are the read roller and reverse roller dirty? NO YES Clean the rollers. Is the reverse flapper working properly? NO Adjust the reverse solenoid. 5 - 33 AR-651/810 TROUBLE SHOOTING
Page 1 and 2: 5. TROUBLESHOOTING 5.1 Diagnosis an
Page 3 and 4: [E09] Jam caused by an abnormal HDD
Page 5 and 6: [E25] External LCF transport jam (p
Page 7 and 8: [E21] Paper fed from the 1st casset
Page 9 and 10: [E33] Paper fed from the 3rd casset
Page 11 and 12: [E3F] Paper fed from the tandem LCF
Page 13 and 14: [EB6] Paper left on the transport p
Page 15 and 16: [E12] Bypass misfeeding (paper not
Page 17 and 18: [E14] 2nd cassette misfeeding (pape
Page 19 and 20: [E16] 4th cassette misfeeding (pape
Page 21 and 22: 5.1.3 Cover open jam [E41] Front co
Page 23 and 24: [E47] Feed cover opened during prin
Page 25 and 26: [E51] Leading edge of paper not rea
Page 31: [E59] Leading edge of paper not rea
Page 35 and 36: [E7A] RADF opened during original f
Page 37 and 38: 5. 1. 6. Paper jam in finisher [E9F
Page 39 and 40: [EA3] Paper remaining inside the fi
Page 41 and 42: Is the door switch working properly
Page 43 and 44: [EA6] Finisher early arrival jam Is
Page 45 and 46: [EA9] Saddle stitcher door opened d
Page 47 and 48: [EAB] Saddle stitcher transport sto
Page 49 and 50: [EB3] Ready time time-out jam Is th
Page 51 and 52: [EC2] Inserter reverse path delay j
Page 53 and 54: 5. 1. 7. Paper feeding system relat
Page 55 and 56: [C18] Abnormal tandem LCF tray-up m
Page 57 and 58: [C1C] External LCF tray motor drivi
Page 59 and 60: [CD4] Toner bag full (1) Check the
Page 61 and 62: [C27] Carriage home position sensor
Page 63 and 64: [C43] Abnormal thermistor after abn
Page 65 and 66: [C47] Abnormal IH power voltage/IH
Page 67 and 68: [C4A] Cleaning web finished (1) Che
Page 69 and 70: [C58] Communication error between t
Page 71 and 72: 5.1.12 ADF related service call [C7
Page 73 and 74: [C83] Original length sensor adjust
Page 75 and 76: [C86] Large original exit sensor ad
Page 77 and 78: [CA3] Secondary scanning coarse adj
Page 79 and 80: 5. 1. 14 . Finisher related service
Page 81 and 82: [CB2] Abnormal delivery motor Rotat
Page 83 and 84:
Is the tray 2 home position sensor
Page 85 and 86:
[CB6] Abnormal stapler shift motor
Page 87 and 88:
[CB8] Abnormal backup RAM data Is t
Page 89 and 90:
[CBA] Abnormal saddle stitcher stit
Page 91 and 92:
[CBF] Abnormal saddle stitcher pape
Page 93 and 94:
[CC1] Abnormal Saddle stitcher micr
Page 95 and 96:
[CC2] Communication error between f
Page 97 and 98:
[Procedure 3] Is the swing motor cl
Page 99 and 100:
[CC6] Abnormal punch motor (with AR
Page 101:
5. 1. 15. Service call for others [
show all

SHARP TROUBLE & ERROR CODES AR-651, AR-810 - OlsonBros

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?