SHARP TROUBLE & ERROR CODES AR-651, AR-810 - OlsonBros

More documents

Recommendations

Info

[C48] IGBT high temperature 1. Check the operation of the IH fan Check if the IH fan is rotating normally. (Is the connector securely connected?) 2. Check the IH control board (1) Check if the IGBT or IGBT radiation plate are normal. (Is the radiation plate securely attached?) (2) Check if the conductor pattern on the board is short- or open-circuited. (3) Replace the IH control board. 3. Clear the status counter Change the values “12”, “14”, “15” or “18” of the status counter (08-400) to “0”. * The status counter value is as follows in the following cases. Change them to "0" respectively. •The error occurred before the temperature of the fuser roller reaches 40°C: "12" •The error occurred before the temperature of the fuser roller reaches 150°C: "15" •The error occurred before the machine has become ready: "14" •The error occurred when the machine is in the ready state: "18" [C49] Abnormal IH circuit or coil 1. Check the IH control board (1) Check if the conductor pattern on the board is short or open-circuited. (2) Replace the IH control board. 2. Check the IH coil (1) Check if the coil is broken or shorted. (2) Replace the IH coil. 3. Clear the status counter Change the values “13”, “15”, “16” or “19” of the status counter (08-400) to “0”. * The status counter value is as follows in the following cases. Change them to "0" respectively. •The error occurred before the temperature of the fuser roller reaches 40°C: "13" •The error occurred before the temperature of the fuser roller reaches 150°C: "16" •The error occurred before the machine has become ready: "15" •The error occurred when the machine is in the ready state: "19" [C47], [C48] and [C49] can be cleared by turning OFF and ON the main switch as long as the problem was solved, and the status counter does not have to be changed to "0". The value of the status counter remains until the next service call overwrites the value. AR-651/810 TROUBLE SHOOTING 5 - 66
[C4A] Cleaning web finished (1) Check if the cleaning web is remaining. (2) Check if the connector J332 on the LGC board is not disconnected. (3) Check if there is no abnormality at the web sensor. (4) Replace the LGC board. [CD5] Abnormality at the web motor signal path (1) Check if the connector of the web motor and connector pins are not disconnected. (2) Check if the drawer connector and connector pins are not disconnected. (3) Check if the harness between the drawer connector and the web motor is not open-circuited. (4) Check if the connector of the LGC board and connector pins are not disconnected. (5) Check if the harness between the connector of the LGC board and the drawer connector is not open- circuited. (6) Replace the LGC board. (7) Replace the fuser unit. 5 - 67 AR-651/810 TROUBLE SHOOTING
Page 1 and 2:
5. TROUBLESHOOTING 5.1 Diagnosis an
Page 3 and 4:
[E09] Jam caused by an abnormal HDD
Page 5 and 6:
[E25] External LCF transport jam (p
Page 7 and 8:
[E21] Paper fed from the 1st casset
Page 9 and 10:
[E33] Paper fed from the 3rd casset
Page 11 and 12:
[E3F] Paper fed from the tandem LCF
Page 13 and 14:
[EB6] Paper left on the transport p
Page 15 and 16: [E12] Bypass misfeeding (paper not
Page 17 and 18: [E14] 2nd cassette misfeeding (pape
Page 19 and 20: [E16] 4th cassette misfeeding (pape
Page 21 and 22: 5.1.3 Cover open jam [E41] Front co
Page 23 and 24: [E47] Feed cover opened during prin
Page 25 and 26: [E51] Leading edge of paper not rea
Page 33 and 34: 5.1.5 Original jam in RADF [E71] Or
Page 35 and 36: [E7A] RADF opened during original f
Page 37 and 38: 5. 1. 6. Paper jam in finisher [E9F
Page 39 and 40: [EA3] Paper remaining inside the fi
Page 41 and 42: Is the door switch working properly
Page 43 and 44: [EA6] Finisher early arrival jam Is
Page 45 and 46: [EA9] Saddle stitcher door opened d
Page 47 and 48: [EAB] Saddle stitcher transport sto
Page 49 and 50: [EB3] Ready time time-out jam Is th
Page 51 and 52: [EC2] Inserter reverse path delay j
Page 53 and 54: 5. 1. 7. Paper feeding system relat
Page 55 and 56: [C18] Abnormal tandem LCF tray-up m
Page 57 and 58: [C1C] External LCF tray motor drivi
Page 59 and 60: [CD4] Toner bag full (1) Check the
Page 61 and 62: [C27] Carriage home position sensor
Page 63 and 64: [C43] Abnormal thermistor after abn
Page 65: [C47] Abnormal IH power voltage/IH
Page 69 and 70: [C58] Communication error between t
Page 71 and 72: 5.1.12 ADF related service call [C7
Page 73 and 74: [C83] Original length sensor adjust
Page 75 and 76: [C86] Large original exit sensor ad
Page 77 and 78: [CA3] Secondary scanning coarse adj
Page 79 and 80: 5. 1. 14 . Finisher related service
Page 81 and 82: [CB2] Abnormal delivery motor Rotat
Page 83 and 84: Is the tray 2 home position sensor
Page 85 and 86: [CB6] Abnormal stapler shift motor
Page 87 and 88: [CB8] Abnormal backup RAM data Is t
Page 89 and 90: [CBA] Abnormal saddle stitcher stit
Page 91 and 92: [CBF] Abnormal saddle stitcher pape
Page 93 and 94: [CC1] Abnormal Saddle stitcher micr
Page 95 and 96: [CC2] Communication error between f
Page 97 and 98: [Procedure 3] Is the swing motor cl
Page 99 and 100: [CC6] Abnormal punch motor (with AR
Page 101: 5. 1. 15. Service call for others [
show all

SHARP TROUBLE & ERROR CODES AR-651, AR-810 - OlsonBros

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?