SHARP TROUBLE & ERROR CODES AR-651, AR-810 - OlsonBros

More documents

Recommendations

Info

[Procedure 2] Is the switch actuator for the front door working properly? YES NO Fix the mechanism. Is the front cover switch (MS2S) working normally? YES NO Replace the switch. Measure the voltage of J11-12 on the saddle switcher controller PC board when the front door is opened. Is it 5V? YES NO The front door opening/closing sensor is broken. Replace it. Replace the saddle stitcher controller PC board. [Procedure 3] Is the switch actuator for the delivery door working properly? YES NO Fix the mechanism. Is the delivery cover switch working normally? YES NO Replace the switch. Measure the voltage of J11-9 on the saddle stitcher controller PC board when the delivery door is opened. Is it 5V ? YES NO The delivery cover sensor (PI3S) is broken. Replace it. Replace the saddle stitcher controller PC board. AR-651/810 TROUBLE SHOOTING 5 - 94
[CC2] Communication error between finisher and saddle stitcher Is the problem solved by turning OFF and ON the power switch of the copier? NO YES END Is the wiring between the finisher controller PC board and the saddle stitcher controller PC board connected? NO YES Connect the wiring. Measure the voltage between J3-2 (+) and J3-1 (-) on the finisher controller PC board. Is it DC 5V? YES NO Replace the finisher controller PC board. Replace the saddle stitcher controller PC board. 5 - 95 AR-651/810 TROUBLE SHOOTING
Page 1 and 2:
5. TROUBLESHOOTING 5.1 Diagnosis an
Page 3 and 4:
[E09] Jam caused by an abnormal HDD
Page 5 and 6:
[E25] External LCF transport jam (p
Page 7 and 8:
[E21] Paper fed from the 1st casset
Page 9 and 10:
[E33] Paper fed from the 3rd casset
Page 11 and 12:
[E3F] Paper fed from the tandem LCF
Page 13 and 14:
[EB6] Paper left on the transport p
Page 15 and 16:
[E12] Bypass misfeeding (paper not
Page 17 and 18:
[E14] 2nd cassette misfeeding (pape
Page 19 and 20:
[E16] 4th cassette misfeeding (pape
Page 21 and 22:
5.1.3 Cover open jam [E41] Front co
Page 23 and 24:
[E47] Feed cover opened during prin
Page 25 and 26:
[E51] Leading edge of paper not rea
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
5.1.5 Original jam in RADF [E71] Or
Page 35 and 36:
[E7A] RADF opened during original f
Page 37 and 38:
5. 1. 6. Paper jam in finisher [E9F
Page 39 and 40:
[EA3] Paper remaining inside the fi
Page 41 and 42:
Is the door switch working properly
Page 43 and 44: [EA6] Finisher early arrival jam Is
Page 45 and 46: [EA9] Saddle stitcher door opened d
Page 47 and 48: [EAB] Saddle stitcher transport sto
Page 49 and 50: [EB3] Ready time time-out jam Is th
Page 51 and 52: [EC2] Inserter reverse path delay j
Page 53 and 54: 5. 1. 7. Paper feeding system relat
Page 55 and 56: [C18] Abnormal tandem LCF tray-up m
Page 57 and 58: [C1C] External LCF tray motor drivi
Page 59 and 60: [CD4] Toner bag full (1) Check the
Page 61 and 62: [C27] Carriage home position sensor
Page 63 and 64: [C43] Abnormal thermistor after abn
Page 65 and 66: [C47] Abnormal IH power voltage/IH
Page 67 and 68: [C4A] Cleaning web finished (1) Che
Page 69 and 70: [C58] Communication error between t
Page 71 and 72: 5.1.12 ADF related service call [C7
Page 73 and 74: [C83] Original length sensor adjust
Page 75 and 76: [C86] Large original exit sensor ad
Page 77 and 78: [CA3] Secondary scanning coarse adj
Page 79 and 80: 5. 1. 14 . Finisher related service
Page 81 and 82: [CB2] Abnormal delivery motor Rotat
Page 83 and 84: Is the tray 2 home position sensor
Page 85 and 86: [CB6] Abnormal stapler shift motor
Page 87 and 88: [CB8] Abnormal backup RAM data Is t
Page 89 and 90: [CBA] Abnormal saddle stitcher stit
Page 91 and 92: [CBF] Abnormal saddle stitcher pape
Page 93: [CC1] Abnormal Saddle stitcher micr
Page 97 and 98: [Procedure 3] Is the swing motor cl
Page 99 and 100: [CC6] Abnormal punch motor (with AR
Page 101: 5. 1. 15. Service call for others [
show all

SHARP TROUBLE & ERROR CODES AR-651, AR-810 - OlsonBros

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?