datasheet (3).pdf - EEWeb

More documents

Recommendations

Info

dsPIC33FJ32MC302/304, dsPIC33FJ64MCX02/X04 AND dsPIC33FJ128MCX02/X04 FIGURE 26-2: CRC GENERATOR RECONFIGURED FOR x 16 + x 12 + x 5 + 1 SDOx XOR D Q BIT 0 p_clk 26.2 User Interface 26.2.1 DATA INTERFACE D Q BIT 4 p_clk To start serial shifting, a ‘1’ must be written to the CRCGO bit. The module incorporates a FIFO that is 8 deep when PLEN (PLEN) > 7, and 16 deep, otherwise. The data for which the CRC is to be calculated must first be written into the FIFO. The smallest data element that can be written into the FIFO is one byte. For example, if PLEN = 5, then the size of the data is PLEN + 1 = 6. The data must be written as follows: data[5:0] = crc_input[5:0] data[7:6] = ‘bxx Once data is written into the CRCWDAT MSb (as defined by PLEN), the value of VWORD (VWORD) increments by one. The serial shifter starts shifting data into the CRC engine when CRCGO = 1 and VWORD > 0. When the MSb is shifted out, VWORD decrements by one. The serial shifter continues shifting until the VWORD reaches 0. Therefore, for a given value of PLEN, it will take (PLEN + 1) * VWORD number of clock cycles to complete the CRC calculations. When VWORD reaches 8 (or 16), the CRCFUL bit will be set. When VWORD reaches 0, the CRCMPT bit will be set. To continually feed data into the CRC engine, the recommended mode of operation is to initially “prime” the FIFO with a sufficient number of words so no interrupt is generated before the next word can be written. Once that is done, start the CRC by setting the CRCGO bit to ‘1’. From that point onward, the VWORD bits should be polled. If they read less than 8 or 16, another word can be written into the FIFO. D Q BIT 5 p_clk D Q To empty words already written into a FIFO, the CRCGO bit must be set to ‘1’ and the CRC shifter allowed to run until the CRCMPT bit is set. Also, to get the correct CRC reading, it will be necessary to wait for the CRCMPT bit to go high before reading the CRCWDAT register. If a word is written when the CRCFUL bit is set, the VWORD Pointer will roll over to 0. The hardware will then behave as if the FIFO is empty. However, the condition to generate an interrupt will not be met; therefore, no interrupt will be generated (See Section 26.2.2 “Interrupt Operation”). At least one instruction cycle must pass after a write to CRCWDAT before a read of the VWORD bits is done. 26.2.2 INTERRUPT OPERATION When the VWORD4:VWORD0 bits make a transition from a value of ‘1’ to ‘0’, an interrupt will be generated. 26.3 Operation in Power-Saving Modes 26.3.1 SLEEP MODE If Sleep mode is entered while the module is operating, the module will be suspended in its current state until clock execution resumes. 26.3.2 IDLE MODE To continue full module operation in Idle mode, the CSIDL bit must be cleared prior to entry into the mode. If CSIDL = 1, the module will behave the same way as it does in Sleep mode; pending interrupt events will be passed on, even though the module clocks are not available. DS70291E-page 310 © 2011 Microchip Technology Inc. BIT 12 p_clk CRC Read Bus D Q BIT 15 p_clk CRC Write Bus
dsPIC33FJ32MC302/304, dsPIC33FJ64MCX02/X04 AND dsPIC33FJ128MCX02/X04 26.4 Registers The CRC module provides the following registers: • CRC Control Register • CRC XOR Polynomial Register REGISTER 26-1: CRCCON: CRC CONTROL REGISTER U-0 U-0 R/W-0 R-0 R-0 R-0 R-0 R-0 — — CSIDL VWORD bit 15 bit 8 R-0 R-1 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CRCFUL CRCMPT — CRCGO PLEN bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 CSIDL: CRC Stop in Idle Mode bit 1 = Discontinue module operation when device enters Idle mode 0 = Continue module operation in Idle mode bit 12-8 VWORD: Pointer Value bits Indicates the number of valid words in the FIFO. Has a maximum value of 8 when PLEN > 7, or 16 when PLEN ≤ 7. bit 7 CRCFUL: FIFO Full bit 1 = FIFO is full 0 = FIFO is not full bit 6 CRCMPT: FIFO Empty Bit 1 = FIFO is empty 0 = FIFO is not empty bit 5 Unimplemented: Read as ‘0’ bit 4 CRCGO: Start CRC bit 1 = Start CRC serial shifter 0 = Turn off the CRC serial shifter after the FIFO is empty bit 3-0 PLEN: Polynomial Length bits Denotes the length of the polynomial to be generated minus 1. © 2011 Microchip Technology Inc. DS70291E-page 311
Page 1 and 2:
dsPIC33FJ32MC302/304, dsPIC33FJ64MC
Page 3 and 4:
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
© 2011 Microchip Technology Inc. D
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260: dsPIC33FJ32MC302/304, dsPIC33FJ64MC
Page 309: dsPIC33FJ32MC302/304, dsPIC33FJ64MC
Page 329 and 330: © 2011 Microchip Technology Inc. D
Page 361 and 362:
Page 363 and 364:
Page 365 and 366:
Page 367 and 368:
Page 369 and 370:
Page 371 and 372:
Page 373 and 374:
Page 375 and 376:
Page 377 and 378:
Page 379 and 380:
Page 381 and 382:
Page 383 and 384:
Page 385 and 386:
Page 387 and 388:
Page 389 and 390:
Page 391 and 392:
Page 393 and 394:
Page 395 and 396:
Page 397 and 398:
Page 399 and 400:
Page 401 and 402:
Page 403 and 404:
Page 405 and 406:
Page 407 and 408:
Page 409 and 410:
Page 411 and 412:
Page 413 and 414:
Page 415 and 416:
Page 417 and 418:
Page 419 and 420:
Page 421 and 422:
Page 423 and 424:
Page 425 and 426:
Page 427 and 428:
Page 429 and 430:
Page 431 and 432:
Page 433 and 434:
Page 435 and 436:
show all

datasheet (3).pdf - EEWeb

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?