INSTALLATION MANUAL - Smarthome

More documents

Recommendations

Info

123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 3.5 Communicator Setup Checklist The Communicator (Dialer) can dial up to 8 phone numbers plus RP. Digital reporting formats include: Pulse 4+2, SIA, Contact ID, and Pager. There is also a Voice † format which can be commanded from the RP Rules Programming to call a persons home or cellphone and deliver a voice message. Use the following checklist for each required telephone number. 1. Under Menu 08 - Telephone Account Setup, select one of the telephone numbers and program the following: Option 01: Select the desired reporting format - 0=Disable, 1=Contact ID, 2=SIA, 3=Pulse 4+2, 4=Pager, 5=Voice † Note: The Voice format (5) cannot be enabled from keypad programming. It can only be programmed from the Elk-RP Software using the Whenever/And/Then Rules. Option 02: Set the priority for the first (primary number) to 0 = Always Report. Option 03: Program the telephone number digits to be dialed. No special start or ending characters are required. Option 04: Set the dial attempts to greater than 0. For Digital reports 8 is suggested. For Voice the max. is 2. Option 05 Program the digits for the account number to report. Each area (partition) has its own Acct. Number. Option 13: Select Yes to have Area info, Zone Alarms, Zone Restores, and Zone Unbypasses reported to this Tel #. Option 14: Select Yes if you wish to have Zone Bypasses reported to this Tel #. Option 15: Select Yes if you wish to have Zone Troubles reported to this Tel #. Option 16: Select Yes if you wish to have User (Open/Close) Reports reported to this Tel #. Option 17: Select Yes if you wish to have Global System Events (AC Fail, Low Battery, etc.) reported to this Tel #. Option 18: Although not required, you may program a text name for each telephone number. 2. Under Menu 09 - Area Reporting Codes, select the area (partition) and program the desired options such as: Dialer Delay, Alarm Abort, Auto Open/Closings, etc. then . 3. Under Menu 10 - Zone Reporting Codes, select the zone number and program the desired options such as: Zone Alarms, Restores, Bypasses, or Trouble. Option A: For Zone Alarm program a two digit code. To have the automatic SIA or Contact ID report codes transmitted simply program a nonzero value. I.E. Program a 1 (01). Option R: For Zone Restore program a two digit code. For automatic SIA or Contact ID codes program a 1 (01). Option B: For Zone Bypass program a two digit code. For automatic SIA or Contact ID codes program a 1 (01). Option T: For Zone Trouble program a two digit code. For automatic SIA or Contact ID codes program a 1 (01). 4. Under Menu 11 - F Key Reporting Codes, select and program the alarm code for each desired Keypad Panic Key. NOTE: Keypad Panics only have Alarm report codes, they do not have restore codes. For automatic SIA or Contact ID codes program a 1 (01). 5. Under Menu 12 - Sys Report Code Options & Codes, select and program each desired option such as: AC Fail, Low Battery, Automatic Test, and other system wide options, including the time values for certain options. For automatic SIA or Contact ID report codes program a 1 (01). 6. Under Menu 13 - User Report Codes, select and and program an Open or Close report code for any User(s) that you wish to track arm/disarm events, including arm/disarm by the Installer Code or Elk-RP computer. 3.6 Entering Installer Level Programming 1. Press the center ‘ELK’ key once followed by the DOWN arrow key until display reads “9-Installation Programming”. NOTE: The keypad may beep and display the following: 2. Enter the Installer Program Code when required. Press the right arrow key to select the “Installation Programming” option. The Factory Default Installer Program Code is: 1 7 2 8 3 9 Auth. Required Enter Valid Pin 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 123456789012345678901234567890121234 For security against unauthorized programming changes, the installer code should be changed from its factory default setting. This can be done from Menu 07 - Globals System Definitions, Option 42. Once the Installer Code has been entered, the first programming menu will display and a 4 minute timer will be started. If there is no key-press activity during this time period the control will automatically exit from the programming mode. It is easy to navigate around and between the programming menus and options using the up and down arrow keys. When the correct menu or option is located, press the right arrow key to proceed into that menu. Refer to the Quick Reference Guide on the following page to locate a particular menu or to see what options appear under each menu. Refer to the individual menus and their option descriptions for details about each of the programmable items. † Not evaluated by UL Page 22 M1G Installation and Programming
ELK-M1G QUICK REFERENCE - MENU PROGRAMMING Menu 01 Menu 04 Menu 06 Menu 07 Menu 08 Menu 10 Menu 13 Bus Mod Enroll Keypad Defs Cutoff Timers Global Options (cont.) Telephone #’s & Accts Zone Rpt Codes User Rpt Codes Keypad 1 (1) Burglar (26) Out 2 Change to Voltage Telephone #1 Zone #1 User #1 Enrolling (1) Area Assgn (2) Fire (27) Out 2 Delay Time (1) Always Report Alarm Code (1) Open Code -Disp Totat Modules (2) Silent Entry (3) Medical (28) Out 2 Sgl Alarm Lockout (2) Number Restore Code Close Code -Allow Module Edit (3) Silent Exit (4) Police (29) Rings til Answer (3) Format Bypass Code (4) Silent Chime (5) Carbon Mon (30) Ring/Hang/Answer (4) Attempts Trouble Code User 100 Menu 02 (5) Dark in 60 sec (6) Emergency (31) 2 Way Listen-in Enable (5) Acct #1 - Installer- User Code Auth. (6) Show Date/Time (7) Freeze (32) 2 Way Callback Time (6) Acct #2 Menu 11 (1) Open Code User 1 (7) Show Temp (8) Gas (33) CS Alm Verify Time (7) Acct #3 Keypad Close Code (1) Area # (8) Show Area (9) Heat (34) Baud Rate Port 0 (8) Acct #4 Report Codes (2) Arm (9) Byp Req Code (10) Water (35) Xmit Event Log (9) Acct #5 Keypad 1 User 101 (3) Disarm (10) F1 Key Def. (11) Aux1 24hr (36) Xmit Zone Changes (10) Acct #6 (1) F1 Key Alarm - RP Computer (4) Bypass (11) F2 Key Def (12) Aux2 24hr (37) Xmit Output Changes (11) Acct #7 (2) F2 Key Alarm Upload/Download (5) Access (12) F3 Key Def (38) Xmit Task Changes (12) Acct #8 (3) F3 Key Alarm (1) Open Code (6) Temporary (13) F4 Key Def (39) Xmit Light Changes (13) Report Area/Alm (4) F4 Key Alarm Close Code (7) Master (14) F5 Key Def Menu 07 (40) Xmit Keypad Keys /Rest/Unbypass (5) F5 Key Alarm (8) Menu 1-5 (15) F6 Key Def Global Options (41) Req Code User Menus 1-5 (14) Report Zn Bypass (6) F6 Key Alarm Menu 14 (9) Duress (16) [Name] (1) Tel Remote (42) Local Prog. Code (15) Report Zn Troubles Wireless Defs (10) [Name] (2) 12hr TimeDisp (43) Serial Number [Read Only] (16) Report User Op/Cl 1: ReceiverOptions (3) DD/MM Disp. (44) Software Ver. [Read Only] (17) Report Sys Globals (1) Receiver Size Menu 03 Menu 05 (4) Celcius Disp. (45) Default Control Options (18) [Name] (2) ZnBank(Start Zn) Area Defs Zone Defs (5) DST Observe (81) Default User Codes (3) Reg Supv. Hrs. Area 1 Zone 1 (6) Fast Loop Tm (82) Default Areas Data Menu 09 Menu 12 (4) Fire Supv. Hrs. (1) Exit Delay 1 (1) Definition (7) SlowLoop Tm (83) Default Keypads Data Area Report Codes System Rpt Codes 2: Transmitter Opts (2) Entry Delay 1 (2) Type (8) Cross SelfVer (84) Default Zones Data Area 1 (1) AC Fail Delay ^ Select Transmitter (3) Exit Delay 2 (3) Area Assign (9) Cross Zn Tm (85) Default Zone Names (1) Dial Delay Time (2) AC Fail Code (1) Enable Xmtr. (4) Entry Delay 2 (4) Silent Alarm (10) Aud Trbls (86) Default Cutoff Timers (2) Abort Code (3) Auto Test Code (2) Supv. Type (5) Auto Stay (5) Dialer Delay (11) 6 digit codes (87) Default Global Data (3) Cancel Time (4) TstTime hr:mm (3) Enable Option 1 (6) Exit Restart (6) Listen-In (12) CodeLockout (88) Default Telephone Data (4) Cancel Code (5) Days betweenTest (4) Enable Option 2 (7) Closing Ringback (7) Bypass (13) Common Area (89) Default Telephone Numbers (5) Close Auto (6) Aux Overcurrent (5) Keyfob User ID (8) SglKey Quickarm (8) Force Arm (14) Out1 Yelp to Buz (90) Default Area Report Codes (6) Close Early (7) Exp Module Tbl 3: Learn Transmitter (9) DblKey Quickarm (9) Swinger (15) Out1 Start Vol. (91) Default Zone Report Codes (7) Close Extended (8) Installer Begin ^ Select Transmitter (10) StayKeyScroll (10) Per. Trip (16) Out1 Max. Alm. (92) Default System Report Codes (8) Fail to Close (9) Installer End (1) Xmtr to Learn (11) Stay Instant (11) Fast Loop (17) Out1 Max. Voice (93) Default User Report Codes (9) Late Close (10) Log 80% Full (2) Push Xmtr (12) Night Scroll (12) Chime (18) Out1 Max. NonAlm (94) Default Voice Messages (10) Keyswitch Close (11) Low Battery 4: Keyfob Event Def. (13) Night Instant (13) Cross Zn (19) Out1 ‘No Talk’ (95) Default Wireless Definitions (11) Duress Code (12) Memory Error (1) Button 1 Code (14) StayChgArmed (14) [Name] (20) Out1 Say Sys (99) Default Entire Control Panel (12) Open After Alarm (13) RP Download (2) Button 2 Code (15) [Name] (21) Out1 Say Alms (13) Open Early (14) Tel Line Fault (3) Button 3 Code (22) Out1 Say Zn Status (14) Fail to Open (15) Output 2 Tbl (4) Button 4 Code (23) Out1 Say Sys Tbl (15) Open Late (5) Button 5 Code (24) Out1 Say Zn Tbl (16) Keyswitch Open (6) Button 6 Code (25) Out1 Say Chime (17) User Lockout (7) Button 7 Code (18) Exit Error (8) Button 8 Code (19) Fail to Comm M1G Installation and Programming Page 23
Page 1 and 2: INSTALLATION MANUAL Cross Platform
Page 3 and 4: Table of Contents Specifications, F
Page 5 and 6: Specifications, Features, and Benef
Page 7 and 8: J5 J3 JP2 B A - NEG C + +12V PLC Mo
Page 9 and 10: Data Bus Cable CAT5 or CAT6 Recomme
Page 11 and 12: AC Failure, Low Battery, and Automa
Page 13 and 14: 1234567890123456789012345 123456789
Page 15 and 16: 2.5 Keypad Overview Ready Light - O
Page 17 and 18: 123456789012345678901234567890 1234
Page 19 and 20: 123456789012345678901234567890 1234
Page 21: Section 3 - Programming The Control
Page 25 and 26: 12345678901234567890123456789012123
Page 27 and 28: 12345678901234567890123456789012123
Page 29 and 30: 12345678901234567890123456789012123
Page 31 and 32: 12345678901234567890123456789012123
Page 33 and 34: 12345678901234567890123456789012123
Page 35 and 36: 12345678901234567890123456789012123
Page 37 and 38: 12345678901234567890123456789012123
Page 39 and 40: 12345678901234567890123456789012123
Page 41 and 42: 12345678901234567890123456789012123
Page 43 and 44: 12345678901234567890123456789012123
Page 45 and 46: 12345678901234567890123456789012123
Page 47 and 48: 12345678901234567890123456789012123
Page 49 and 50: Section 4 - PC Programming and Auto
Page 51 and 52: 4.3 Automation Rules and Attributes
Page 53 and 54: † VOICE - This section is used to
Page 55 and 56: RULES - This section essentially br
Page 57 and 58: Examples of Rules - Shown below are
Page 59 and 60: Appendix A - Event Codes (cont.) Ev
Page 61 and 62: Appendix B - Telephone Remote Contr
Page 63 and 64: Appendix C - Voice Message Vocabula
Page 65 and 66: Appendix E - SIA CP-01 Compliance
Page 67 and 68: Appendix F - Regulatory Agency Stat
Page 69 and 70: Appendix G - Additional ELK-M1KP Ke
Page 71 and 72: A Alarm Abort 40 Alarm Cutoff Timer

INSTALLATION MANUAL - Smarthome

Create successful ePaper yourself

Delete template?

Save as template?