specification for subdivision construction of road works and drainage

More documents

Recommendations

Info

The Contractor shall ensure that all flammable materials are used and stored in accordance with the Explosives and Dangerous Goods Act and any other statute or regulation governing storage and use of such materials, and shall obtain such permits and licenses and pay all relevant fees and charges. P10 VANDALISM The Contractor shall allow for all reasonable measures to protect the Works and the operations therein from acts of vandalism. The Contractor shall allow for any remedial action required as a consequence of such acts. Vandalism shall not be an excluded risk. P11 HOURS OF WORK Unless with prior approval in writing from the Engineer, the Contractor shall not conduct works on Sundays, Public Holidays or between the hours of 6 pm on any day and 7 am on the following day except those works required in respect to safety or maintenance of Site conditions, such as dewatering activities. P12 CODES AND AUSTRALIAN STANDARDS Where an Australian Standard is specified, the Contractor shall construct and conduct the Works in accordance with the provisions of that standard. Where an Australian Standard has not been specified, the Contractor shall allow for the construction of the Works in compliance with the provisions of the Australian Standard covering the class or type of work being constructed. In the event that a Standard other than an Australian Standard is specified, the Contractor shall allow for complying with the provisions of the specified Standard. The Standard applying shall be the latest edition at the time of commencement of the Contract. Copies of Australian Standards may be purchased from the Standards Association of Australia. The following documents shall apply to this Contract. AS1012 AS1141 AS1160 AS1181 AS1289 AS1348 AS1379 AS1470 AS1597 AS1646 Methods of Testing Concrete Methods for Sampling and Testing Aggregates Bitumen Emulsions for Construction and Maintenance of Pavements Method of Measurement of Civil Engineering Works and Associated Building Works Methods of Testing Soils for Engineering Purposes Glossary of Terms-Road and Traffic Engineering Specification and Supply of Concrete Health and Safety at Work - Principles and Practices Precast Reinforced Concrete Box Culverts Elastomeric Seals for Water Works Purposes AS1742 Manual of Uniform Traffic Control Devices 5 Specification for Subdivision Construction of Road Works and Drainage Rev. 1 – February 2013
AS1743 AS1744 AS2008 AS2053 AS2150 AS2157 AS2341 AS2648 AS2700 AS2701 AS2758 AS2876 AS2891 AS3600 AS3679 AS3700 AS3725 AS3727 AS3798 AS3972 AS3996 AS4058 AS4455 AS4671 AS4680 AS4801 Road Signs - Specifications Forms of Letters and Numerals for Road Signs Residual Bitumen for Pavements Conduits and Fittings for Electrical Installations Hot Mix Asphalt Cutback Bitumen Methods of Testing Bitumen and Related Road Making Products Underground Marking Tape Colour Standards for General Purposes Methods of Sampling and Testing Mortar for Masonry Construction Aggregates and Rock for Engineering Purposes Concrete Kerb and Channel (Gutters) Methods of Sampling and Testing Asphalt Concrete Structures Structural Steel Masonry Structures Design for Installation of Buried Concrete Pipes Guide to Residential Pavements Guidelines on Earthwork for Commercial and Residential Developments Portland and Blended Cements Access Covers and Grates Precast Concrete Pipes Masonry Units and Segmented Pavers Steel Reinforcing Materials Hot Dip Galvanized Coatings on Fabricated Ferrous Articles Occupational Health and Safety Management Systems Main Roads WA Traffic Management for Roadworks Code of Practice 2000 WA Govt. WA Govt. WA Govt. The Explosives and Dangerous Goods Act Construction Safety Act and Regulations Noise Abatement Act and Regulations Institute of Public Works Engineering Australia (WA Division) – Local Government Guidelines for Subdivision Development Department of Environment - A Guideline for the Prevention of Dust and Smoke Pollution from Land Development Sites in Western Australia (November 1996) 6 Specification for Subdivision Construction of Road Works and Drainage Rev. 1 – February 2013
Page 1 and 2: SPECIFICATION FOR SUBDIVISION CONST
Page 3 and 4: P29 SPECIFICATION TO BE TREATED AS
Page 5 and 6: R6.1 General ......................
Page 7 and 8: Not withstanding the pavement desig
Page 9: The Contractor shall instruct emplo
Page 13 and 14: The Contractor shall at all times m
Page 15 and 16: The Contractor shall be responsible
Page 17 and 18: E SITE PREPARATION AND EARTHWORKS E
Page 19 and 20: The Contractor shall allow for any
Page 21 and 22: D D1 DRAINAGE GENERAL Stormwater dr
Page 23 and 24: The term "Coarse Aggregate" is used
Page 25 and 26: Where over excavation has occurred,
Page 27 and 28: The aggregate shall be clean and un
Page 29 and 30: Asphalt + 5mm + 5mm + 100mm Surface
Page 31 and 32: NOMINAL SIZE (mm) PERCENTAGE PASSIN
Page 33 and 34: Notwithstanding this Specification
Page 35 and 36: Aggregate Grading Limits Sieve Size
Page 37 and 38: Generally the application rate will
Page 39 and 40: R4.2.7 Finish The completed seal sh
Page 41 and 42: Surface preparation, which shall in
Page 43 and 44: R4.3.6 Joints and Junctions All lon
Page 45 and 46: The acceptance of the asphalt surfa
Page 47 and 48: R6.5 Compaction of Bricks A high fr
Page 49 and 50: The spacing of guide posts shall be
Page 51 and 52: R11.2 Temporary Signing and Linemar

specification for subdivision construction of road works and drainage

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?