2008 Manual of Motorcycle Sport - Motorcycling Australia

More documents

Recommendations

Info

160 enjoy the ride at saddle height must be 50mm, d) The dimensions of the sidecar baseboard in plan view, taken from a line drawn no further rearwards than the lowest point of the front downtube to the forward most point of the sidecar wheel tyre and terminating no further rearwards than a line drawn at right angles to the machine from the rearmost point of the rear tyre, must be: i) At least 760mm long adjacent to the sidecar wheel, ii) At least 300mm wide with at least 25mm radius to all corners. e) There must be no more than 50mm between baseboard and motorcycle and between baseboard and sidecar wheel. The baseboard must be arranged so as not to allow the passenger’s feet to be trapped, f) There must be no less than 4 sidecar attachment points, g) Stirrup fitting for the passenger’s feet are not permitted, h) Handholds: i) Must be finished with a loop of at least 100mm, ii) Must not project beyond a line taken with the outer edge of the sidecar mudguard or bodywork, iii) Adjacent to the nose section of the sidecar and less than 200mm from the track surface must be at an angle of at least 45° from the horizontal, i) The rear end of the rear wheel mudguard must terminate not more than 65° above a horizontal line drawn through the rear wheel axle and be valanced to baseboard level on the inside, j) The sidecar mudguard must cover at least 135° of the periphery of the wheel and be valanced to baseboard level on the inside, k) No machine may be fitted with scoop or paddle tyres, l) Suspension travel must not exceed: i) 152mm (6”) measured at the front axle, ii) 102mm (4”) at the rear axle. m) Rear tyre width must not exceed 135mm (5.3”), n) Brakes: i) Front - single caliper, single disc may be fitted provided they were manufactured before 31 st December 1974, ii) Rear - rear disc brakes may be used provided they were fitted as standard equipment for that particular combination. 18.8.0.2 Pre-1985 is for sidecars contructed from frames and motors manufactured before 31 st December 1984 18.9 ENGINES - Sidecars - classic MX & Dirt Track 18.9.0.1 For the Pre-1975 class, all performance parts must be manufactured before 31 st December 1974 and comply with the following: a) Only round-slide carburettors manufactured within the relevant period may be used. b) Engine capacity must be: i) Up to 1300cc, ii) Within the tolerances in GCR 12.4 18.9.0.2 Pre-1968 will be for sidecars constructed from road going frames and all major components be those commercially available within the period. This class will have a trial period of 2 years (2006/2007). 18.9.0.3 The following table sets out the machines and components which eligibility Scrutineers may use as a guide in determining eligibility. Entrants must prove eligibility of machines not listed below. MAKE MODEL(S) Wasp All up to and including RT2, RT8 and RT14 Hagon All up to 31 st December 1974 Yamaha XS 650 all models Honda Any K series Norton All 750, 850 to MK2 only Weslake All up to 850cc and 31 st December 1974 Triumph All up to T150 CCM All BSA B50 based models 2008 MANUAL OF MOTORCYCLE SPORT
18.10 Eligibility - CLASSIC LONG TRACK 18.10.0.1 Engines must have been manufactured before 31 st December 1976. 18.10.0.2 Competitors must be aged at least 30 years at the date of the competition. 18.11 FrameS & pARTS - Classic Long Track 18.11.0.1 The frame must: a) Have conventional swingarm rear suspension with twin shock absorbers, b) Have a front wheel diameter of 23” (594mm), c) Have a rear wheel diameter of 19” (482mm) or 22” (560mm), as specified in the SR. d) Have rear tyres with a maximum tread pattern depth of 8mm. e) Not be fitted leading-link front forks. 18.11.1 Engine Specifications - Solo 18.11.1.1 The engine must: a) Be single cylinder, b) Be 2- valve with push rod operation, c) Have a single spark plug, d) Have a maximum capacity of 500cc + / - 2% tolerance, e) Be vertical in the chassis, f) Be fitted with a round slide carburettor of 38mm maximum bore, g) Not be fitted with a centre port cross flow cylinder head. 18.11.2 Gearbox - Classic Long Track 18.11.2.1 The gearbox must have at least 2 gears. 18.11.3 Frames - Sidecars 18.11.3.1 Conventional type frames as used prior to 31 st December 1976 must be used. 18.11.4 Engine Specifications - Sidecars 18.11.4.1 Engines must have been manufactured before 31 st December 1976. 18.12 Competition Rules - Classic MX and Dirt Track 18.12.0.1 Pre-1960, Pre-1965, Pre-1970. Should a class have insufficient entrants (10) then the entries will compete in the next later period and compete as that class. e.g. Pre-1960 has less than 10 riders, the entrants will then combine with pre-1965 and race as pre-1965. Should that combined class still not have sufficient numbers then both the entrants in pre-1960 and pre-1965 will combine with pre-1970 and race as that class. This GCR applies equally to the pre-1965 250cc who will combine with pre 1970-250cc if there are insufficient numbers for a pre-1965 class. 18.13 AUSTRALIAN classic MOTOCROSS CHAMPIONSHIP 18.13.1.1 The Australian Classic Motocross Championship willbe conducted as a single meeting at a venue selected by the Classic Motocross and Dirt Track Commission. 18.13.1.2 Evolution class may be run as part of the Australian Classic Motocross Championship or independently. 18.13.1.3 The Sidecar Classic Motocross Championship may be run independently from the solo Australian Classic Motocross Championship. 18.14 AUSTRALIAN CLASSIC dirt track CHAMPIONSHIP 18.14.0.1 The Australian Classic Dirt Track Championship shall generally be conducted on either the 2 nd or 3 rd weekend of September each year. 18 classic motocross & dirt track MA MEMBERS GET 10% OFF ARIEL BIKE BATTERIES How? see www.ma.org.au 2008 2007 MANUAL OF MOTORCYCLE SPORT enjoy the ride 161
Page 3 and 4:
Motorcycling Australia 2 0 0 8 M a
Page 5 and 6:
ut still showed his quality by mana
Page 7 and 8:
5 PROTESTS AND APPEALS... .. .. ..
Page 9 and 10:
15.19 Engines - Minimoto... .. .. .
Page 11 and 12:
23.1 Protective Clothing - Moto-Tri
Page 13 and 14:
TABLE OF CONTENTS 2008 MANUAL OF MO
Page 15 and 16:
MOTORCYCLING AUSTRALIA COMMISSIONS
Page 17 and 18:
A SHORT HISTORY OF MOTORCYCLING AUS
Page 19 and 20:
Clubs Clubs are the smallest, but o
Page 21 and 22:
MOTORCYCLING AUSTRALIA HALL OF FAME
Page 23 and 24:
motorcycling australia HALL OF FAME
Page 25 and 26:
2007 AUSTRALIAN CHAMPIONS 2007 AUST
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
2008 AUSTRALIAN motorcyclING calend
Page 33 and 34:
Say something like: “Physical fit
Page 35 and 36:
THE GENERAL COMPETITION RULES THE P
Page 37 and 38:
RULES AND MAKING RULE CHANGES Rules
Page 39 and 40:
Procedure for Consideration of Item
Page 41 and 42:
1 JURISDICTION 1.1 Definitions 1.1.
Page 43 and 44:
i) Prescribe levels of noise, atmos
Page 45 and 46:
2.3 sports development levy 2.3.1 C
Page 47 and 48:
the meeting, k) Order the administr
Page 49 and 50:
2 administration 2.5.11.5 The RCB m
Page 51 and 52:
3.1.2 LICENCE TYPES AND ACTIVITY EL
Page 53 and 54:
legal guardian of the applicant. v)
Page 55 and 56:
4 COMPETITIONS 4.1 Venues 4.1.1 Reg
Page 57 and 58:
4.2.2.5 The permit for an event mus
Page 59 and 60:
MA series event: a) Must be faxed o
Page 61 and 62:
advantage as a result of an unfair
Page 63 and 64:
or directions as the appellate body
Page 65 and 66:
informed of facts in such manner as
Page 67 and 68:
6 JUDICIAL COMMITTEE GUIDELINES 6.1
Page 69 and 70:
competing in International competit
Page 71 and 72:
an applicant must a) Be 18 years or
Page 73 and 74:
9 officials accreditation scheme
Page 75 and 76:
10 NATIONAL PERSONAL ACCIDENT INSUR
Page 77 and 78:
11 ANTI-DOPING POLICY This has been
Page 79 and 80:
and provide accurate and up-to-date
Page 81 and 82:
whereabouts information as required
Page 83 and 84:
disciplinary action against the emp
Page 85 and 86:
11.21.2 Notification to Competitors
Page 87 and 88:
12 ALL DISCIPLINES 12.1 Application
Page 89 and 90:
a measurer. All measurer’s report
Page 91 and 92:
a) At least 1 supporting the forwar
Page 93 and 94:
12.9.3.2 Fuel tests must comply wit
Page 95 and 96:
12.10.3 Use of sound level meters 1
Page 97 and 98:
conduct, or b) Having regard to any
Page 99 and 100:
h) Age group racing: i) Subject to
Page 101 and 102:
13 AUSTRALIAN CHAMPIONSHIPS 13.1 MA
Page 103 and 104:
13.2.8 Categories for Senior Austra
Page 105 and 106:
qualifying or races, c) For Histori
Page 107 and 108:
15 Road racing 15.1 Protective Clot
Page 109 and 110: screen and instruments, but replace
Page 111 and 112: a) Steering damper, b) Ride height
Page 113 and 114: a) Brake pads, linings and brake ho
Page 117 and 118: cylinders, d) Have an engine capaci
Page 119 and 120: property of Formula Xtreme Pty Ltd
Page 121 and 122: o) Fuel injection 15.10.3.6 It is r
Page 123 and 124: 15.12.3.7 The fuel tank breather pi
Page 125 and 126: of the tray. 15.13.2.3 The front of
Page 127 and 128: i) No other alterations or modifica
Page 129 and 130: allowed, iv) No systems not sold or
Page 131 and 132: ) The leading edge of a sidecar mac
Page 133 and 134: a) A maximum capacity of 40 litres,
Page 135 and 136: 16.1.6 Hair and Jewellery 16.1.6.1
Page 137 and 138: 16.5.1.2 Round or Oval number plate
Page 139 and 140: foot controlled. 16.8.3 Period 4 16
Page 141 and 142: 17 MOTOCROSS AND SUPERCROSS 17.1 Pr
Page 145 and 146: CAPACITY RPM Up to 85cc 8,000 85cc
Page 147 and 148: 17.9 competition Rules - Supercross
Page 149 and 150: v) Gear levers, vi) Heavy duty rims
Page 151 and 152: 17.13.1.3 There will be a minimum o
Page 153 and 154: 18 CLASSIC MOTOCROSS & DIRT TRACK 1
Page 155 and 156: a) As per relevant period for the c
Page 157 and 158: Forks Wheels Controls Handlebars Br
Page 159: Montesa King Scorpion & Cappra VR 2
Page 163 and 164: disturbance are not to be used, c)
Page 165 and 166: shape or modified in any way, other
Page 167 and 168: so as to prevent the passenger’s
Page 169 and 170: Fig 19.3.2.4 Carburettor dimensions
Page 171 and 172: a) Obtain approval from the Speedwa
Page 173 and 174: 19.11.7 Late Arrival 19.11.7.1 The
Page 175 and 176: e resolved as follows: a) The compe
Page 177 and 178: nominate 1 competitor for the Speed
Page 179 and 180: 19.12.10.7 Starting positions for t
Page 181 and 182: c) Competitors cannot change gate p
Page 183 and 184: 20 DIRT TRACK 20 dirt track 20.1 Pr
Page 185 and 186: as shown at 12.10.2. 20.4 Machine &
Page 187 and 188: per class 20.10.4.1 The championshi
Page 189 and 190: 21.1.5.2 Visors mounted on the helm
Page 191 and 192: is used, a steel bolt of not less t
Page 193 and 194: 21 track the highest number of poin
Page 195 and 196: 22.2 Engines - quads 22.2.1 Capacit
Page 197 and 198: 23 MOTO-TRIALS 23.1 Protective Clot
Page 199 and 200: with an original capacity of 250cc
Page 201 and 202: 23.7.3.2 The following penalties ap
Page 203 and 204: 24 SUPERMOTO 24 SUPERMOTO 24.1 Prot
Page 205 and 206: 24.7 competition Rules- supermoto 2
Page 207 and 208: 25 ENDURO AND RELIABILITY TRIALS 25
Page 209 and 210: 25.4.1 Courses 25.4.1.1 Courses mus
Page 211 and 212:
25.4.8.2 Competitors must at all ti
Page 213 and 214:
used when refueling. l) No fuel may
Page 215 and 216:
a) Be conducted on a closed circuit
Page 217 and 218:
a) Determine that no penalty should
Page 219 and 220:
seeded The seeded position of rider
Page 221 and 222:
awards. 25.10.3.7 Riders nominated
Page 223 and 224:
26 MINIKHANA 26.1 INTRODUCTION The
Page 225 and 226:
to B Grade. Riders who place 1st in
Page 227 and 228:
26.7 courses- minikhana 26.7.1 Basi
Page 229 and 230:
left. 26.7.11.2 Crossing the finish
Page 231 and 232:
area of 6 metres by 20 metres. 26.7
Page 233 and 234:
26.7.35 Procedure 26.7.35.1 The sta
Page 235 and 236:
28 RECREATIONAL MOTORCYCLE ACTIVITY
Page 237 and 238:
29 NATIONAL TEAM SELECTION POLICY T
Page 239 and 240:
appendix 1 29.0 APPROVAL LABELS FOR
Page 241 and 242:
appendix 2 MODEL SUPPLEMENTARY REGU
Page 243 and 244:
whether change of machine is allowe
Page 245 and 246:
Classes Machine Details and Capacit
Page 247 and 248:
appendix 3 MEMBER PROTECTION POLICY
Page 249 and 250:
that a child is being abused by the
Page 251 and 252:
or otherwise be destroyed with the
Page 253 and 254:
12. Forms of discipline If an indiv
Page 255 and 256:
Attachment A - Code of conduct As a
Page 257 and 258:
Appendix 4- PRIVACY REGULATION We r
Page 260 and 261:
enjoy the ride 2008 RIDERS’ DIVIS
Page 262 and 263:
Welcome to the Riders’ Division M
Page 264 and 265:
motorcycling australia tours Motorc
Page 266 and 267:
selecting an ma event There’s a w
Page 268 and 269:
• Take notice of any hazards iden
Page 270 and 271:
This effort is to help you navigate
Page 272 and 273:
as quick as possible. If you can, p
Page 274 and 275:
Computers Hewlett-Packard National
Page 276:
enjoy the ride 2008 RIDERS’ DIVIS
show all

2008 Manual of Motorcycle Sport - Motorcycling Australia

Create successful ePaper yourself

Delete template?

Save as template?