Tol-O-Matic System Compatibility - Industrial and Bearing Supplies
Tol-O-Matic System Compatibility - Industrial and Bearing Supplies
Tol-O-Matic System Compatibility - Industrial and Bearing Supplies
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
ACTUATOR SELECTION<br />
BASIC SELECTION<br />
The procedure for<br />
selecting an<br />
Axidyne mechanical<br />
actuator depends<br />
on the complexity<br />
of your application.<br />
A simple but<br />
thorough evaluation<br />
of the application’s<br />
motion requirements<br />
is required<br />
including the load<br />
support system,<br />
force requirements<br />
<strong>and</strong> limiting factors.<br />
Use the following<br />
selection procedure<br />
to help determine<br />
the appropriate<br />
actuator configuration<br />
appropriate for<br />
the application.<br />
Selection<br />
SELECTION KEY<br />
REQUIREMENTS<br />
STROKE LENGTH<br />
(in) [mm]<br />
LOAD WEIGHT<br />
(lb) [kg]<br />
LOAD SPEED<br />
(in/sec) [mm/sec]<br />
THRUST FORCE<br />
(lb) [kg]<br />
RESOLUTION/<br />
REPEATABILITY<br />
(in) [mm]<br />
ACTUATOR<br />
ORIENTATION<br />
MOMENT LOADS<br />
(in-lb) [N-m]<br />
DUTY CYCLE<br />
Procedure<br />
1. List Key Requirements<br />
Begin the selection process by identifying actuator key requirements<br />
shown in the chart at left.<br />
2. Determine whether a screw-style or belt-style<br />
actuator is appropriate for your application.<br />
The maximum operating speed of screw actuators is limited by the<br />
critical speed characteristic of the screw. Belt-drive actuators are<br />
used in applications where speed(consult factory for applications<br />
over 100 inches/sec) <strong>and</strong> stroke length requirements exceed screw<br />
critical speed limitations. Screw actuators provide finer resolution<br />
<strong>and</strong> better repeatability than belt-drive units <strong>and</strong> are preferred for<br />
short stroke, high move repetition requirements. (See “Limiting<br />
Factors” in the “Comprehensive Product Selection” section of this<br />
catalog.)<br />
NOTE: Belt-drive actuators are NOT recommended for vertical<br />
applications. Please consult the factory for further information.<br />
3. Evaluate Load Support <strong>System</strong>.<br />
The <strong>Tol</strong>-O-<strong>Matic</strong> Axidyne product family provides a selection of<br />
three load carrier support <strong>and</strong> guidance systems.<br />
A. Adjustable carrier bracket with self-lubricating plastic bearing rods<br />
for BCS <strong>and</strong> BCB series cylinder-style actuators<br />
The BCS series actuators provide good general purpose load<br />
capacity <strong>and</strong> tracking accuracy. Periodic carrier adjustment<br />
<strong>and</strong> bearing rod maintenance may be required.<br />
B. Recirculating bearings on ground steel shafts for SLS10 Series<br />
slide-style actuators. These actuators provide consistent carrier<br />
tracking for full actuator life.<br />
NEW TOL-O-MOTION SIZING<br />
AND SELECTION SOFTWARE!<br />
Leads you through the selection<br />
process step-by-step<br />
making it easy to choose<br />
the right combination of<br />
products in a user friendly<br />
Windows format.<br />
C. Heavy duty enclosed recirculating bearings in gothic arch<br />
guide rail for B3S <strong>and</strong> B3B series actuators.<br />
This series provides the highest load <strong>and</strong> moment load capacity<br />
with consistent tracking <strong>and</strong> low carrier friction for the full<br />
actuator life.<br />
Review the application requirements <strong>and</strong> select the appropriate<br />
actuator style. Then choose either metric or st<strong>and</strong>ard (inch) versions.<br />
66