to download LG Multi V Plus - Hawco

More documents

Recommendations

Info

Troubleshooting Guide Error No. 23* Master 231 Slave1 232 Slave2 233 Error Type Error Point Main Reasons Inverter Compressor DC Link Low Voltage Copyright ©2007 LG Electronics. Inc. All right reserved. Only for training and service purposes DC Voltage isn't charged after starting relay on ■ Error Diagnosis and Countermeasure Flow Chart Is input voltage normal? Yes Is inverter PCB assembly power connection normal? Yes Is inverter PCB assembly normal? Yes Recheck power and installation condition No No No - 96 - 1. DC Link terminal misconnection/terminal contact fault 2. Starting relay damage 3. Condenser damage 4. Inverter PCB assembly damage (DC Link voltage sensing part) 5. Input voltage low Check R~S/S~T/T~R phase voltage is 380V ±10% R~N/S~N/T~N phase voltage is 220V ±10% → Check connection condition and wiring if power is abnormal Check connection between inverter PCB assembly and bridge diode(misconnection, disconnection) → wiring again if abnormality found Check inverter PCB assembly IPM normality → Replace inverter PCB assembly LGE Internal Use Only
* Inverter PCB & bridge diode wiring * Measuring input voltage Copyright ©2007 LG Electronics. Inc. All right reserved. Only for training and service purposes - 97 - Troubleshooting Guide LGE Internal Use Only
Page 1 and 2:
System Outdoor Unit R410A SERVICE M
Page 3 and 4:
Safety Precautions Copyright ©2007
Page 5 and 6:
Ventilate before operating air cond
Page 7 and 8:
Use power cables of sufficient curr
Page 9 and 10:
Safely dispose of the packing mater
Page 11 and 12:
1. Model Names 1.1 Indoor Unit * AR
Page 13 and 14:
2.2 Outdoor Units 2.2.1 Cooling Onl
Page 15 and 16:
3. Combination of Outdoor Units 3.1
Page 17 and 18:
4. Nomenclature 4.1 Indoor Unit ARN
Page 19 and 20:
Part 2 Outdoor Units Copyright ©20
Page 21 and 22:
Function Copyright ©2007 LG Electr
Page 23 and 24:
1.3 Master and slave Unit's EEV con
Page 25 and 26:
2.1.2 Oil return control on heating
Page 27 and 28:
2.3 Stopping operation 2.3.1 Stoppi
Page 29 and 30:
3.2 Discharge temperature control
Page 31 and 32:
4. Other control 4.1 Initial setup
Page 33 and 34:
4.2 Emergency operation - If a comp
Page 35 and 36:
■ Sensor Check Error Code Display
Page 37 and 38:
Liquid Pipe Gas Pipe Procedure 1. A
Page 39 and 40:
CAUTION 1. Guaranteed Temperature r
Page 41 and 42:
4.7 Pump Out This function gathers
Page 43 and 44:
4.8 Auto Back Up Function_Inverter
Page 45 and 46: 4.10 Night Low Noise Function In co
Page 47 and 48: 4.11 Vacuum Mode This function is u
Page 49 and 50: Part 3 PCB Setting and Test Run Cop
Page 51 and 52: 2. How to cope with Test Run abnorm
Page 53 and 54: ■ Checking according to dip switc
Page 55 and 56: Function Dry Contact Snow Forced De
Page 57 and 58: Replacement procedure for Compresso
Page 59 and 60: Part 4 Trouble shooting guide Copyr
Page 61 and 62: Copyright ©2007 LG Electronics. In
Page 63 and 64: 2.2 Fan Motor Checking Item Symptom
Page 65 and 66: • EEV Coil and body(Outdoor unit)
Page 67 and 68: 2.4 Phase Bridge Diode Checking Met
Page 69 and 70: 2.6 Fan IPM Checking Method 2.7 UW1
Page 71 and 72: 2.10 Other Copyright ©2007 LG Elec
Page 73 and 74: Outdoor unit related error Display
Page 77 and 78: Outdoor unit related error Copyrigh
Page 79 and 80: Outdoor unit related error Copyrigh
Page 83 and 84: Error No. 01 Indoor unit air sensor
Page 86 and 87: Troubleshooting Guide float A:Point
Page 88 and 89: Troubleshooting Guide Error No. 06
Page 92 and 93: Troubleshooting Guide Error No. 21*
Page 100 and 101: Troubleshooting Guide * Measuring r
Page 108 and 109: Troubleshooting Guide Error No. Err
Page 110: Troubleshooting Guide Error No. Err
Page 113 and 114: Error No. 52* Master 521 Slave1 522
Page 115 and 116: Error No. Error Type Error Point Ma
Page 117 and 118: Error No. 60* Master 601 Slave1 602
Page 119: Error No. 70* Master 701 Slave1 702
Page 122 and 123: Troubleshooting Guide Measuring inp
Page 140: P/NO : 3828A24006W OCT, 2007
show all

to download LG Multi V Plus - Hawco

Create successful ePaper yourself

Delete template?

Save as template?