B - Quad-Lock Building Systems

More documents

Recommendations

Info

Application Instructions for Peel & Stick Membrane PRODUCT MANUAL 1. All surfaces must be smooth, dry and free of dust, water or any other substance which may hinder adhesion. 2. Concrete (footing) must be cured a minimum of seven (7) days and an adhesion test is recommended before membrane application. Ensure the footing is clean and dry. 3. For membrane applications at temperatures below -5°C (23°F) contact your local peel & stick representative. 4. It’s not necessary to prime Quad-Lock as long as it is clean and dust free. A water-based primer may be used. See manufacturer’s recommendations. 5. All penetrations (pipes, etc.) through the waterproofing membrane, should be pre-treated with an application of liquid membrane/sealant. 6. All inside corners (vertical and horizontal, e.g. along footing) must be pre-stripped with a 6" [152mm] width of membrane centered on the corner. This membrane must be installed in direct contact with the substrate not leaving any voids under the membrane strip. 7. All outside corners must be pre-treated with a 6" [15cm] width strip of membrane centered on the corner. 8. For vertical applications, align the first strip of membrane to one of the grooves in the Quad-Lock Panel. At the top edge of the strip remove approximately 6" [15cm] of the silicone release paper and adhere the membrane to the surface. Affix the remaining portion of the strip by removing the silicone release paper. During application, pass hand over the surface to remove any trapped air and wrinkles. Apply pressure with a hand roller over the membrane to ensure good initial adhesion. 9. Subsequent rolls must be installed in the same way and should be aligned with the preceding roll with a lap of at least 2½" [65mm]. End laps must overlap at least 6" [152mm]. Avoid wrinkles in the membrane at the overlaps (roll the seams with laminate or J-roller). 10. Seal all leading edges (e.g. at top and bottom) and all horizontal overlaps with sealant. 11. Protect the membrane to avoid damage from other trades, construction materials, and backfilling. Use a rated drainage board layer. Consult your Quad-Lock dealer for ideas. Building Tip: Pre-cut peel-and-stick membrane into desired lengths and attach it vertically. Reach around either side of the membrane and remove the backing as you install. Avoid removing all of the backing prior to installation. Always overlap the joints and follow the manufacturer’s recommendations on the use of a protection board before backfilling. Page 116 Chapter 5 – Water/Damp-Proofing July 2009
PRODUCT MANUAL Fastening Dimpled Drainage Board (Typical) CUT DELTA MS TO TERMINATE @ QUAD-LOCK TIES DELTA MS MOLD STRIP FASTENED TO QUAD-LOCK TIES @ 4" & 8" O.C. DELTA MS FASTENER @ 24" O.C. HOR. DELTA MS FASTENER @ 24" O.C. STAGGERED FROM ROW ABOVE QUAD-LOCK TIE SPACING AS PER DIMENSIONS SHOWN DELTA MS FASTENER @ 12" O.C. VER. AT TERMINATION ONLY SEAL JOINT WITH WATER BASED SEALANT PEEL & STICK MEMBRANE EXTEND OVER FOOTING PAD CONCRETE FOOTING Figure 114: Fastening Pattern for Drainage Board 8" 4" 8" 4" July 2009 Chapter 5 – Water/Damp-Proofing Page 117 8" 4" 12" 12"
Page 1 and 2:
PRODUCT MANUAL July 2009 Version 2.
Page 3 and 4:
PRODUCT MANUAL DISCLAIMER QUAD-LOCK
Page 5 and 6:
PRODUCT MANUAL Appendix A - Enginee
Page 7 and 8:
PRODUCT MANUAL Figure 57: Radius Wa
Page 9 and 10:
PRODUCT MANUAL 11 IINNTTRROODDUUCCT
Page 11 and 12:
PRODUCT MANUAL Quad-Lock Panels Reg
Page 13 and 14:
PRODUCT MANUAL Quad-Lock FS Panel T
Page 15 and 16:
PRODUCT MANUAL 5 1 2 " [140mm] 4" [
Page 17 and 18:
PRODUCT MANUAL Slab Tie & Bracket S
Page 19 and 20:
PRODUCT MANUAL which overlap each o
Page 21 and 22:
PRODUCT MANUAL Figure 21: Flex-C Tr
Page 23 and 24:
PRODUCT MANUAL ADVANTAGES, FEATURES
Page 25 and 26:
PRODUCT MANUAL 22 DDEESSIIGGNN && C
Page 27 and 28:
PRODUCT MANUAL Cutting Quad-Lock Co
Page 29 and 30:
PRODUCT MANUAL FOOTINGS When buildi
Page 31 and 32:
PRODUCT MANUAL 6. Make a mark at th
Page 33 and 34:
PRODUCT MANUAL Any of these fastene
Page 35 and 36:
PRODUCT MANUAL Thickened Edge Slab
Page 37 and 38:
PRODUCT MANUAL Figure 36: Panel Pai
Page 39 and 40:
PRODUCT MANUAL Figure 40: Corner As
Page 41 and 42:
PRODUCT MANUAL Nominal Concrete Cav
Page 43 and 44:
PRODUCT MANUAL Figure 45: R-38 Corn
Page 45 and 46:
PRODUCT MANUAL Figure 47: Corner As
Page 47 and 48:
PRODUCT MANUAL Figure 49: Finishing
Page 49 and 50:
PRODUCT MANUAL Cutting Panels for A
Page 51 and 52:
PRODUCT MANUAL Metric Dimensions: f
Page 53 and 54:
PRODUCT MANUAL Figure 54: T-Wall As
Page 55 and 56:
PRODUCT MANUAL Figure 56: Pilaster
Page 57 and 58:
PRODUCT MANUAL Figure 58: Radius Wa
Page 59 and 60:
PRODUCT MANUAL Flex-C Trac ® - Con
Page 61 and 62:
PRODUCT MANUAL Flex-C Angle ® - Co
Page 63 and 64:
PRODUCT MANUAL Figure 60: Extender
Page 65 and 66:
PRODUCT MANUAL Tall Walls Because a
Page 67 and 68:
PRODUCT MANUAL Wall Width Transitio
Page 69 and 70:
PRODUCT MANUAL Double Walls / Commo
Page 71 and 72:
PRODUCT MANUAL Figure 67: Wood Buck
Page 73 and 74: PRODUCT MANUAL Figure 69: Insulated
Page 75 and 76: PRODUCT MANUAL WINDOW ROUGH OPENING
Page 77 and 78: PRODUCT MANUAL ARCHED WINDOW ROUGH
Page 79 and 80: PRODUCT MANUAL WINDOW INSTALLATION:
Page 81 and 82: PRODUCT MANUAL Ledger Installation
Page 83 and 84: PRODUCT MANUAL Pre-Set Ledger Board
Page 85 and 86: PRODUCT MANUAL LEDGER PLACEMENT AND
Page 87 and 88: PRODUCT MANUAL Other Floor Connecti
Page 89 and 90: PRODUCT MANUAL Typical Hollow Core
Page 91 and 92: PRODUCT MANUAL Typical Wall to Floo
Page 93 and 94: PRODUCT MANUAL Typical Roof Rafter
Page 95 and 96: PRODUCT MANUAL SOLID WALL CAP In ca
Page 97 and 98: PRODUCT MANUAL Connection to Existi
Page 99 and 100: PRODUCT MANUAL Pre-Pour: Before con
Page 101 and 102: PRODUCT MANUAL Service Access: Pene
Page 103 and 104: PRODUCT MANUAL Attachment of Access
Page 105 and 106: PRODUCT MANUAL Adequately brace all
Page 107 and 108: PRODUCT MANUAL Wood Bulkheads Figur
Page 109 and 110: PRODUCT MANUAL DRYWALL / GYPSUM The
Page 111 and 112: PRODUCT MANUAL ACRYLIC FINISHES AND
Page 113 and 114: PRODUCT MANUAL SIDING Various types
Page 115 and 116: PRODUCT MANUAL Brick Ledge Brick Le
Page 117 and 118: PRODUCT MANUAL Option 4: 10" to 6"
Page 119 and 120: PRODUCT MANUAL Figure 113: Assembly
Page 121 and 122: PRODUCT MANUAL July 2009 Chapter 4
Page 123: PRODUCT MANUAL 55 WWAATTEERR//DDAAM
Page 127 and 128: PRODUCT MANUAL • Metal Corner Bra
Page 129 and 130: PRODUCT MANUAL July 2009 Chapter 6
Page 131: PRODUCT MANUAL Curing Concrete will
Page 134 and 135: General Hot Weather Concreting Guid
Page 136 and 137: Product/Service Name Icynene Insula
Page 138 and 139: Concrete: PRODUCT MANUAL ACI 216 (T
Page 140 and 141: Concrete Finishes: PRODUCT MANUAL A
Page 142 and 143: Typical Quad-Deck Floor-to Wall Con
Page 144 and 145: Typical Quad-Deck Flat Roof Connect
Page 146 and 147: PRODUCT MANUAL TECHNICAL SPECIFICAT
Page 148 and 149: Wall Widths of Quad-Lock Panel and
Page 150 and 151: PRODUCT MANUAL Fire Resistance Rati
Page 152 and 153: BXUVC.W019 Fire Resistance Ratings
Page 154 and 155: PRODUCT MANUAL 99 PPRRIIMMEERR:: AA
Page 156 and 157: CCMC Evaluation PRODUCT MANUAL Page
Page 158 and 159: PRODUCT MANUAL Page 150 Appendix A
Page 170 and 171: PRODUCT MANUAL The following tables
Page 172 and 173: TABLE 3.4 PRODUCT MANUAL MINIMUM VE
Page 174 and 175:
TABLE 3.6 PRODUCT MANUAL MINIMUM VE
Page 176 and 177:
TABLE 5.5 PRODUCT MANUAL MINIMUM PE
Page 178 and 179:
TABLE 5.8B PRODUCT MANUAL MAXIMUM A
Page 180 and 181:
PRODUCT MANUAL Page 172 Appendix B
Page 182 and 183:
PRODUCT MANUAL Page 174 Appendix B
Page 184 and 185:
PRODUCT MANUAL AAPPPPEENNDDIIXX CC
Page 186:
UK: Evaluation Report: o ULC - BXUV
show all

B - Quad-Lock Building Systems

Create successful ePaper yourself

Delete template?

Save as template?