B - Quad-Lock Building Systems

More documents

Recommendations

Info

PRODUCT MANUAL Place Inside and Outside Corner Brackets over the knobs. Place a Full Tie as close to the corner as you can, making sure that the two flanges are both inserted in the inner corner bracket. Cut flanges from ties and insert them in the outer corner bracket as shown below, making sure that the slots closest to the corner have a flange. Then insert a flange every 4" [10cm] (or 6" [15cm] once so it's next to a heavy grove). Extra flanges can be added around the heavy grooves, if needed for attachment. Now place ties so they straddle each vertical seam and all deep grooves in the panels (every 12" [30cm]). Important: The cut tie flanges placed into the corner brackets are critical structural parts. Do not forget. With Quad-Lock Plus Panels, the Corner Brackets should be placed on the inside row of slots in the panels (close to the inside wall surface). Always make sure that you insert flanges into the brackets. With Quad-Lock FS Panels, cut and install the panels in the same manner as Regular Panels paying attention that the strips will align vertically throughout the wall. Using this method, all the desired fastening strips will be there except the one close to the corner on the left side (seen from the inside). If needed, install a thin metal strip on that side of the corner (screw it to the flanges). Ensure that all fastening strips are held by full ties, split ties, or tie flanges combined with metal brackets. Figure 39: Corner Assembly – Second Course Page 30 Chapter 2 – Design & Construction Details July 2009
PRODUCT MANUAL Figure 40: Corner Assembly with Corner Brackets, 6" [152mm] Wall Figure 41: Corner Assembly with Corner Brackets, 8" [203mm] Wall Building Tip: Flanges for corners can be pre-cut to speed up construction. July 2009 Chapter 2 – Design & Construction Details Page 31
Page 1 and 2: PRODUCT MANUAL July 2009 Version 2.
Page 3 and 4: PRODUCT MANUAL DISCLAIMER QUAD-LOCK
Page 5 and 6: PRODUCT MANUAL Appendix A - Enginee
Page 7 and 8: PRODUCT MANUAL Figure 57: Radius Wa
Page 9 and 10: PRODUCT MANUAL 11 IINNTTRROODDUUCCT
Page 11 and 12: PRODUCT MANUAL Quad-Lock Panels Reg
Page 13 and 14: PRODUCT MANUAL Quad-Lock FS Panel T
Page 15 and 16: PRODUCT MANUAL 5 1 2 " [140mm] 4" [
Page 17 and 18: PRODUCT MANUAL Slab Tie & Bracket S
Page 19 and 20: PRODUCT MANUAL which overlap each o
Page 21 and 22: PRODUCT MANUAL Figure 21: Flex-C Tr
Page 23 and 24: PRODUCT MANUAL ADVANTAGES, FEATURES
Page 25 and 26: PRODUCT MANUAL 22 DDEESSIIGGNN && C
Page 27 and 28: PRODUCT MANUAL Cutting Quad-Lock Co
Page 29 and 30: PRODUCT MANUAL FOOTINGS When buildi
Page 31 and 32: PRODUCT MANUAL 6. Make a mark at th
Page 33 and 34: PRODUCT MANUAL Any of these fastene
Page 35 and 36: PRODUCT MANUAL Thickened Edge Slab
Page 37: PRODUCT MANUAL Figure 36: Panel Pai
Page 41 and 42: PRODUCT MANUAL Nominal Concrete Cav
Page 43 and 44: PRODUCT MANUAL Figure 45: R-38 Corn
Page 45 and 46: PRODUCT MANUAL Figure 47: Corner As
Page 47 and 48: PRODUCT MANUAL Figure 49: Finishing
Page 49 and 50: PRODUCT MANUAL Cutting Panels for A
Page 51 and 52: PRODUCT MANUAL Metric Dimensions: f
Page 53 and 54: PRODUCT MANUAL Figure 54: T-Wall As
Page 55 and 56: PRODUCT MANUAL Figure 56: Pilaster
Page 57 and 58: PRODUCT MANUAL Figure 58: Radius Wa
Page 59 and 60: PRODUCT MANUAL Flex-C Trac ® - Con
Page 61 and 62: PRODUCT MANUAL Flex-C Angle ® - Co
Page 63 and 64: PRODUCT MANUAL Figure 60: Extender
Page 65 and 66: PRODUCT MANUAL Tall Walls Because a
Page 67 and 68: PRODUCT MANUAL Wall Width Transitio
Page 69 and 70: PRODUCT MANUAL Double Walls / Commo
Page 71 and 72: PRODUCT MANUAL Figure 67: Wood Buck
Page 73 and 74: PRODUCT MANUAL Figure 69: Insulated
Page 75 and 76: PRODUCT MANUAL WINDOW ROUGH OPENING
Page 77 and 78: PRODUCT MANUAL ARCHED WINDOW ROUGH
Page 79 and 80: PRODUCT MANUAL WINDOW INSTALLATION:
Page 81 and 82: PRODUCT MANUAL Ledger Installation
Page 83 and 84: PRODUCT MANUAL Pre-Set Ledger Board
Page 85 and 86: PRODUCT MANUAL LEDGER PLACEMENT AND
Page 87 and 88: PRODUCT MANUAL Other Floor Connecti
Page 89 and 90:
PRODUCT MANUAL Typical Hollow Core
Page 91 and 92:
PRODUCT MANUAL Typical Wall to Floo
Page 93 and 94:
PRODUCT MANUAL Typical Roof Rafter
Page 95 and 96:
PRODUCT MANUAL SOLID WALL CAP In ca
Page 97 and 98:
PRODUCT MANUAL Connection to Existi
Page 99 and 100:
PRODUCT MANUAL Pre-Pour: Before con
Page 101 and 102:
PRODUCT MANUAL Service Access: Pene
Page 103 and 104:
PRODUCT MANUAL Attachment of Access
Page 105 and 106:
PRODUCT MANUAL Adequately brace all
Page 107 and 108:
PRODUCT MANUAL Wood Bulkheads Figur
Page 109 and 110:
PRODUCT MANUAL DRYWALL / GYPSUM The
Page 111 and 112:
PRODUCT MANUAL ACRYLIC FINISHES AND
Page 113 and 114:
PRODUCT MANUAL SIDING Various types
Page 115 and 116:
PRODUCT MANUAL Brick Ledge Brick Le
Page 117 and 118:
PRODUCT MANUAL Option 4: 10" to 6"
Page 119 and 120:
PRODUCT MANUAL Figure 113: Assembly
Page 121 and 122:
PRODUCT MANUAL July 2009 Chapter 4
Page 123 and 124:
PRODUCT MANUAL 55 WWAATTEERR//DDAAM
Page 125 and 126:
PRODUCT MANUAL Fastening Dimpled Dr
Page 127 and 128:
PRODUCT MANUAL • Metal Corner Bra
Page 129 and 130:
PRODUCT MANUAL July 2009 Chapter 6
Page 131:
PRODUCT MANUAL Curing Concrete will
Page 134 and 135:
General Hot Weather Concreting Guid
Page 136 and 137:
Product/Service Name Icynene Insula
Page 138 and 139:
Concrete: PRODUCT MANUAL ACI 216 (T
Page 140 and 141:
Concrete Finishes: PRODUCT MANUAL A
Page 142 and 143:
Typical Quad-Deck Floor-to Wall Con
Page 144 and 145:
Typical Quad-Deck Flat Roof Connect
Page 146 and 147:
PRODUCT MANUAL TECHNICAL SPECIFICAT
Page 148 and 149:
Wall Widths of Quad-Lock Panel and
Page 150 and 151:
PRODUCT MANUAL Fire Resistance Rati
Page 152 and 153:
BXUVC.W019 Fire Resistance Ratings
Page 154 and 155:
PRODUCT MANUAL 99 PPRRIIMMEERR:: AA
Page 156 and 157:
CCMC Evaluation PRODUCT MANUAL Page
Page 158 and 159:
PRODUCT MANUAL Page 150 Appendix A
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
PRODUCT MANUAL The following tables
Page 172 and 173:
TABLE 3.4 PRODUCT MANUAL MINIMUM VE
Page 174 and 175:
TABLE 3.6 PRODUCT MANUAL MINIMUM VE
Page 176 and 177:
TABLE 5.5 PRODUCT MANUAL MINIMUM PE
Page 178 and 179:
TABLE 5.8B PRODUCT MANUAL MAXIMUM A
Page 180 and 181:
PRODUCT MANUAL Page 172 Appendix B
Page 182 and 183:
PRODUCT MANUAL Page 174 Appendix B
Page 184 and 185:
PRODUCT MANUAL AAPPPPEENNDDIIXX CC
Page 186:
UK: Evaluation Report: o ULC - BXUV
show all

B - Quad-Lock Building Systems

Create successful ePaper yourself

Delete template?

Save as template?