Buderus Manual on Trenchless Installation of Ductile Cast ... - Duktus

More documents

Recommendations

Info

BLS ® restrained joint DN 80 to DN 500 DN Dimensions [mm] Ø d 1 Ø D 1) t PFA 2)* Possible angular deflection 3) Number of locks Technical data sheets Lock set [kg] 80 ** 98 1 127 110 ° 3 0.70 100 ** 118 182 13 100 ° 3 0.83 12 1 20 1 3 100 ° 3 1.13 1 0 170 239 1 0 7 ° 3 1.3 200 222 293 1 0 3 ° 3 1.9 2 0 27 3 7 1 ° 3 2.70 300 32 10 170 0 ° 2.70 00 29 21 190 30 3° . 0 00 23 3 200 30 3° . 0 1) Guideline value 2) PFA: Allowable component operating pressure in bars, up to DN 250 includes high-pressure lock 3) When of the nominal dimensions *) Basis for calculation is wall thickness class K9; higher pressures available on request **) Wall thickness class K10 Retaining chamber Left lock Catch Right lock Welding bead TYTON ® gasket Socket 99
Technical data sheets BLS ® restrained joint DN 600 to DN 1000 100 DN Retaining chamber Locking segment Dimensions [mm] Ø d 1 Ø D 1) t Welding bead PFA 2) TYTON ® gasket Possible angular deflection Socket Number of locks Clamping rings 00 3 732 17 32 2° 9 9 700 738 8 9 197 2 1. ° 10 11 800 8 2 9 0 209 1 /2 3) 1. ° 10 1 900 9 1073 221 1 /2 3) 1. ° 13 13 1000 10 8 1188 233 10/2 3) 1. ° 1 1 1) Guideline value 2) PFA: Allowable component operating pressure in bars, up to DN 250 includes high-pressure lock 3) Wall thickness class K10 Note: The locking segments must be fixed in place with a clamping strap! See installation instructions
Page 1 and 2:
Buderus Ma
Page 3 and 4:
Buderus Ma
Page 6 and 7:
1. Introduction Introduction When t
Page 8 and 9:
Buderus Ma
Page 10 and 11:
At x 100 magnification, these graph
Page 12 and 13:
10 3 kp cm Fig. 2.7 Steel Ductile G
Page 14 and 15:
Fig. 2.11 How the pipes are produce
Page 16 and 17:
2.3 Development in the joint-making
Page 18 and 19:
joints is DVGW Arbeitsblatt GW 3 8
Page 20 and 21:
Longitudinal force-fit joints and t
Page 22 and 23:
Longitudinal force-fit joints and t
Page 24 and 25:
2.3.2 Making the BLS ® joint Makin
Page 26 and 27:
Fig. 2.21 Left lock Catch Right loc
Page 28 and 29:
2.4 Inside and outside protection I
Page 30 and 31:
Inside and outside protection the c
Page 32 and 33:
Reference documents [2.8] Gaebelein
Page 34 and 35:
General What is said above is true
Page 36 and 37:
Other pluses that the two technique
Page 38 and 39:
Fig. 3.5 Hydraulic unit The press-p
Page 40 and 41:
3.2 The auxiliary pipe technique Th
Page 42 and 43:
In the final stage of the operation
Page 44 and 45:
3.4 Requirements for the site Requi
Page 46 and 47:
Reference documents
Page 48 and 49:
Both the variants of the burst lini
Page 50 and 51: During the pulling process, the tra
Page 52 and 53: 4.3.2 Joints As in virtually all tr
Page 54 and 55: Reference documents 3
Page 56 and 57: Fig. 5.3 Assembly of the string of
Page 58 and 59: the outlet nozzles. In rocky soils,
Page 60 and 61: 5.3 General requirements Companies
Page 62 and 63: A prerequisite for this procedure i
Page 64 and 65: Table .1 provides an overview of th
Page 66 and 67: Installations Nominal size DN lengt
Page 68 and 69: Reference documents [ . ] DVGW Arbe
Page 70 and 71: Fig. 6.2 Traction vehicle Fig. 6.3
Page 72 and 73: 6.4 Joints The longitudinal force-f
Page 74 and 75: Areas of application, advantages an
Page 76 and 77: Reference documents 7
Page 78 and 79: 7. 2 A description of the technique
Page 80 and 81: Buderus Giesserei
Page 82 and 83: Fig. 7.8 Pushing in a pipe A descri
Page 84 and 85: 7.5 Reference installations No. Loc
Page 86 and 87: [7. ] Rink, W.: Langrohrrelining mi
Page 88 and 89: In the second step, the pilot is up
Page 90 and 91: 8.3 Outside protection Outside prot
Page 92 and 93: 8.6 Reference documents [8.1] Richt
Page 94 and 95: A consideration of the economics of
Page 96 and 97: A consideration of the economics of
Page 98 and 99: [9.2] DVGW-Hinweis W 09: Auswirkung
Page 102 and 103: Technical data sheets 101
Page 104 and 105: General Pipes must not be: • drop
Page 106 and 107: Filling in the pipe pit DN 80 - DN
Page 108 and 109: DN 80 - DN 00 BLS ® joints There m
Page 110 and 111: Use of clamping ring joints DN 80 -
Page 112 and 113: Notice on assembly DN 80 - DN 00 BL
Page 114 and 115: Retrospective application of weldin
Page 116 and 117: 11.2 Installation instructions for
Page 118 and 119: Inserting the locking segments DN 0
Page 120 and 121: Angular deflection DN 00 - DN 1000
Page 122 and 123: Disconnecting BLS ® joint disconne
Page 124 and 125: Shrink-on devices and protective ta
Page 126 and 127: ZMU Before a pipe is cut, the ZMU s
Page 128 and 129: ZMU 127
Page 130 and 131: 129
Page 132 and 133: 131
show all

Buderus Manual on Trenchless Installation of Ductile Cast ... - Duktus

Create successful ePaper yourself

Delete template?

Save as template?