Buderus Manual on Trenchless Installation of Ductile Cast ... - Duktus

More documents

Recommendations

Info

3.4 Requirements for the site Requirements for the new pipe It goes without saying that when trenchless installation techniques are being, exacting demands are made not only on the pipes and the accessories but also on the machinery used by the companies doing the work and on their qualified specialist personnel. There has to be sophisticated quality assurance system in this case to ensure a high standard of safety and quality for the new pipeline. The company provides evidence that it is suitably qualified by having the appropriate certification under DVGW Arbeitsblatt GW 301 [3. ] in supplementary group GN 1. This ensures that the pipeline which is installed by trenchless means will meet the demands that are made on it not only from the point of view of cost of installation but also in the long term, even beyond the full operating life that is demanded. For a deposit, <strong>Buderus</strong> Giesserei Wetzlar GmbH will supply traction heads, which can also be used for other trenchless installation techniques, on hire. There are now a wide variety of variant traction heads which can be obtained through machinery suppliers. Fig. 3.17 ZMU-PLUS sockets and an inserting end 3
Trenchless replacement of gas and water pipelines 3.5 Reference documents [3.1] DVGW Arbeitsblatt GW 322-1: Grabenlose Auswechslung von Gas- und Wasserrohrleitungen – Teil 1: Press-/Ziehverfahren – Anforderungen, Gütesicherung und Prüfung) [Trenchless replacement of gas and water pipelines – Part 1: Presspull method – Requirements, quality assurance and testing] [3.2] DVGW-Arbeitsblatt GW 322-2: Grabenlose Auswechslung von Gas- und Wasserrohrleitungen – Teil 2: Hilfsrohrverfahren – Anforderungen, Gütesicherung und Prüfung [Trenchless replacement of gas and water pipelines – Part 2: Auxiliary pipe method – Requirements, quality assurance and testing] [3.3] DIN EN : Rohre, Formstücke, Zubehörteile aus duktilem Gusseisen und ihre Verbindungen für Wasserleitungen – Anforderungen und Prüfverfahren [Ductile iron pipes, fittings, accessories and their joints for water pipelines – Requirements and test methods] [3. ] DVGW-Arbeitsblatt GW 301: Qualifikationskriterien für Rohrleitungsbauunternehmen [Qualification criteria for pipeline construction companies]
Page 1 and 2: Buderus Ma
Page 6 and 7: 1. Introduction Introduction When t
Page 10 and 11: At x 100 magnification, these graph
Page 12 and 13: 10 3 kp cm Fig. 2.7 Steel Ductile G
Page 14 and 15: Fig. 2.11 How the pipes are produce
Page 16 and 17: 2.3 Development in the joint-making
Page 18 and 19: joints is DVGW Arbeitsblatt GW 3 8
Page 20 and 21: Longitudinal force-fit joints and t
Page 22 and 23: Longitudinal force-fit joints and t
Page 24 and 25: 2.3.2 Making the BLS ® joint Makin
Page 26 and 27: Fig. 2.21 Left lock Catch Right loc
Page 28 and 29: 2.4 Inside and outside protection I
Page 30 and 31: Inside and outside protection the c
Page 32 and 33: Reference documents [2.8] Gaebelein
Page 34 and 35: General What is said above is true
Page 36 and 37: Other pluses that the two technique
Page 38 and 39: Fig. 3.5 Hydraulic unit The press-p
Page 40 and 41: 3.2 The auxiliary pipe technique Th
Page 42 and 43: In the final stage of the operation
Page 46 and 47: Reference documents
Page 48 and 49: Both the variants of the burst lini
Page 50 and 51: During the pulling process, the tra
Page 52 and 53: 4.3.2 Joints As in virtually all tr
Page 54 and 55: Reference documents 3
Page 56 and 57: Fig. 5.3 Assembly of the string of
Page 58 and 59: the outlet nozzles. In rocky soils,
Page 60 and 61: 5.3 General requirements Companies
Page 62 and 63: A prerequisite for this procedure i
Page 64 and 65: Table .1 provides an overview of th
Page 66 and 67: Installations Nominal size DN lengt
Page 68 and 69: Reference documents [ . ] DVGW Arbe
Page 70 and 71: Fig. 6.2 Traction vehicle Fig. 6.3
Page 72 and 73: 6.4 Joints The longitudinal force-f
Page 74 and 75: Areas of application, advantages an
Page 76 and 77: Reference documents 7
Page 78 and 79: 7. 2 A description of the technique
Page 80 and 81: Buderus Giesserei
Page 82 and 83: Fig. 7.8 Pushing in a pipe A descri
Page 84 and 85: 7.5 Reference installations No. Loc
Page 86 and 87: [7. ] Rink, W.: Langrohrrelining mi
Page 88 and 89: In the second step, the pilot is up
Page 90 and 91: 8.3 Outside protection Outside prot
Page 92 and 93: 8.6 Reference documents [8.1] Richt
Page 94 and 95:
A consideration of the economics of
Page 96 and 97:
A consideration of the economics of
Page 98 and 99:
[9.2] DVGW-Hinweis W 09: Auswirkung
Page 100 and 101:
BLS ® restrained joint DN 80 to DN
Page 102 and 103:
Technical data sheets 101
Page 104 and 105:
General Pipes must not be: • drop
Page 106 and 107:
Filling in the pipe pit DN 80 - DN
Page 108 and 109:
DN 80 - DN 00 BLS ® joints There m
Page 110 and 111:
Use of clamping ring joints DN 80 -
Page 112 and 113:
Notice on assembly DN 80 - DN 00 BL
Page 114 and 115:
Retrospective application of weldin
Page 116 and 117:
11.2 Installation instructions for
Page 118 and 119:
Inserting the locking segments DN 0
Page 120 and 121:
Angular deflection DN 00 - DN 1000
Page 122 and 123:
Disconnecting BLS ® joint disconne
Page 124 and 125:
Shrink-on devices and protective ta
Page 126 and 127:
ZMU Before a pipe is cut, the ZMU s
Page 128 and 129:
ZMU 127
Page 130 and 131:
129
Page 132 and 133:
131
show all

Buderus Manual on Trenchless Installation of Ductile Cast ... - Duktus

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?