Buderus Manual on Trenchless Installation of Ductile Cast ... - Duktus

More documents

Recommendations

Info

11.2 Installation instructions for DN 600 - DN 1000 BLS ® joints Applicability DN 00 - DN 1000 BLS ® joints These installation instructions apply to ductile cast iron pipes and fittings with longitudinal force-fit BLS ® restrained joints. Where appropriate the installation instructions for pipes with cement mortar coatings (ZMU) should be followed. In the case of buried pipelines, the number of joints to be locked has to be decided in accordance with DVGW Arbeitsblatt GW 3 8. The permitted tractive forces for trenchless installation techniques are laid down in DVGW Arbeitsblätter GW 321, 322-1, 323 and 32 (draft), or see section 2, page 20, Table 2.1. Construction of the DN 600 - DN 1000 joint X Retaining chamber Welding bead Locking segment Clamping strap Inserting end TYTON ® gasket Number of locking segments per joint Socket Openings in socket View on X DN 00 700 800 900 1000 n 9 10 10 13 1 11
Installation instructions Cleaning The locking segments and those surfaces of the seating for the gasket, the retaining groove and the locking chamber which are indicated by arrows should be cleaned and any build-ups of paint should be removed. A scraper, e.g. a bent screwdriver, should be used to clean the retaining grooves. Clean the inserting end. Assembling the joint Fitting the TYTON ® gasket (see pp. 10 -107) The opening in the end-face of the socket should always be positioned at the crown of the pipe. Use the laying tool to push the inserting end of the pipe into the socket of the pipe which is already in place until it is in abutment. 11
Page 1 and 2:
Buderus Ma
Page 3 and 4:
Buderus Ma
Page 6 and 7:
1. Introduction Introduction When t
Page 8 and 9:
Buderus Ma
Page 10 and 11:
At x 100 magnification, these graph
Page 12 and 13:
10 3 kp cm Fig. 2.7 Steel Ductile G
Page 14 and 15:
Fig. 2.11 How the pipes are produce
Page 16 and 17:
2.3 Development in the joint-making
Page 18 and 19:
joints is DVGW Arbeitsblatt GW 3 8
Page 20 and 21:
Longitudinal force-fit joints and t
Page 22 and 23:
Longitudinal force-fit joints and t
Page 24 and 25:
2.3.2 Making the BLS ® joint Makin
Page 26 and 27:
Fig. 2.21 Left lock Catch Right loc
Page 28 and 29:
2.4 Inside and outside protection I
Page 30 and 31:
Inside and outside protection the c
Page 32 and 33:
Reference documents [2.8] Gaebelein
Page 34 and 35:
General What is said above is true
Page 36 and 37:
Other pluses that the two technique
Page 38 and 39:
Fig. 3.5 Hydraulic unit The press-p
Page 40 and 41:
3.2 The auxiliary pipe technique Th
Page 42 and 43:
In the final stage of the operation
Page 44 and 45:
3.4 Requirements for the site Requi
Page 46 and 47:
Reference documents
Page 48 and 49:
Both the variants of the burst lini
Page 50 and 51:
During the pulling process, the tra
Page 52 and 53:
4.3.2 Joints As in virtually all tr
Page 54 and 55:
Reference documents 3
Page 56 and 57:
Fig. 5.3 Assembly of the string of
Page 58 and 59:
the outlet nozzles. In rocky soils,
Page 60 and 61:
5.3 General requirements Companies
Page 62 and 63:
A prerequisite for this procedure i
Page 64 and 65:
Table .1 provides an overview of th
Page 66 and 67: Installations Nominal size DN lengt
Page 68 and 69: Reference documents [ . ] DVGW Arbe
Page 70 and 71: Fig. 6.2 Traction vehicle Fig. 6.3
Page 72 and 73: 6.4 Joints The longitudinal force-f
Page 74 and 75: Areas of application, advantages an
Page 76 and 77: Reference documents 7
Page 78 and 79: 7. 2 A description of the technique
Page 80 and 81: Buderus Giesserei
Page 82 and 83: Fig. 7.8 Pushing in a pipe A descri
Page 84 and 85: 7.5 Reference installations No. Loc
Page 86 and 87: [7. ] Rink, W.: Langrohrrelining mi
Page 88 and 89: In the second step, the pilot is up
Page 90 and 91: 8.3 Outside protection Outside prot
Page 92 and 93: 8.6 Reference documents [8.1] Richt
Page 94 and 95: A consideration of the economics of
Page 96 and 97: A consideration of the economics of
Page 98 and 99: [9.2] DVGW-Hinweis W 09: Auswirkung
Page 100 and 101: BLS ® restrained joint DN 80 to DN
Page 102 and 103: Technical data sheets 101
Page 104 and 105: General Pipes must not be: • drop
Page 106 and 107: Filling in the pipe pit DN 80 - DN
Page 108 and 109: DN 80 - DN 00 BLS ® joints There m
Page 110 and 111: Use of clamping ring joints DN 80 -
Page 112 and 113: Notice on assembly DN 80 - DN 00 BL
Page 114 and 115: Retrospective application of weldin
Page 118 and 119: Inserting the locking segments DN 0
Page 120 and 121: Angular deflection DN 00 - DN 1000
Page 122 and 123: Disconnecting BLS ® joint disconne
Page 124 and 125: Shrink-on devices and protective ta
Page 126 and 127: ZMU Before a pipe is cut, the ZMU s
Page 128 and 129: ZMU 127
Page 130 and 131: 129
Page 132 and 133: 131
show all

Buderus Manual on Trenchless Installation of Ductile Cast ... - Duktus

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?