Overview in PDF format - Tallinna TehnikaÃ¼likool

More documents

Recommendations

Info

Faculty of Mechanical EngineeringDepartment of MachineryTALLINN UNIVERSITY OF TECHNOLOGYDissertation was accepted for the commencement of the degree of Doctor ofPhilosophy in Engineering Sciences on June 21, 2006Supervisors:Prof Jyri Papstel , Faculty of Mechanical EngineeringProf Rein Küttner, Faculty of Mechanical EngineeringOpponents:Frid Kaljas, PhD, Bosch Rexroth Oy, EstoniaProf Petri Kuosmanen, PhD, TKK, FinlandCommencement: August 31, 2006Declaration: Hereby I declare that this doctoral thesis, my original investigation andachievement, submitted for the doctoral degree at Tallinn University ofTechnology has not been submitted for any degree or examination.Copyright Tauno Otto, 2006ISSN 1406-4758ISBN 9985-59-641-22
MASINA- JA APARAADIEHITUS E283
Page 1: THESIS ON MECHANICAL AND INSTRUMENT
Page 5 and 6: PREFACEThe mankind of the 21 st cen
Page 7 and 8: Paper I............................
Page 9 and 10: XII. Riives, J., Papstel, J., Otto,
Page 11 and 12: 1. INTRODUCTION1.1. BackgroundManuf
Page 13 and 14: database by a query; c. Search of t
Page 15 and 16: Porter’s Diamond Model task an on
Page 17 and 18: Figure 2.1 Use of modelling in prod
Page 19 and 20: However, it should be noticed that
Page 21 and 22: Figure 2.6 Depth of field/magnifica
Page 23 and 24: 2.3. Prediction of machining accura
Page 25 and 26: uFy=ybsinptyOl 1ulFAϕFigure 2.10 C
Page 27 and 28: is2.5. Dynamical model with two deg
Page 29 and 30: According to de Moivre’s formulaw
Page 31 and 32: constant of the lathe. Figure 2.11
Page 33 and 34: Analogically, test results and resu
Page 35 and 36: Figure 3.1 Model checking in an ope
Page 37 and 38: Figure 3.3 A snapshot of Uppaal mod
Page 39 and 40: Figure 3.5 FMS at TUTM9M8M4M1M2M7M5
Page 41 and 42: Turning and milling operations can
Page 43 and 44: 4. MODELS FOR MONITORING THE RESOUR
Page 45 and 46: As assumptions to solve the queries
Page 47 and 48: Regarding co-operation networks the
Page 49 and 50: • The system offers dynamic and u
Page 51 and 52: Figure 4.5 Associations in the Inno
Page 53 and 54:
An enterprise-centred mapping and a
Page 55 and 56:
Better efficiency and transparency
Page 57 and 58:
institutions: in enterprises of div
Page 59 and 60:
1. Tehnoloogiaseadme tasemel on loo
Page 61 and 62:
REFERENCESAltintas, Y. (2000). Manu
Page 63 and 64:
Russo, M.F. (1999). Automating Scie
Page 65 and 66:
Paper IIAryassov, G., Otto, T., Gro
Page 67 and 68:
Paper IVOtto, T., Papstel, J., Riiv
Page 69 and 70:
ELULOOKIRJELDUS (CV)1. IsikuandmedE
Page 71 and 72:
CURRICULUM VITAE (CV)1. Personal da
Page 73 and 74:
DISSERTATIONS DEFENDED ATTALLINN UN
show all

Overview in PDF format - Tallinna TehnikaÃ¼likool

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?