AXF magnetic flowmeter - Istec Corp.

33 Table of Optional Specifications (Size 2.5 mm (0.1 in.) to 400 mm (16 in.)) (continued)Applicable Model: Available –: Not availableGeneralExplosion proofSubmersibleSanitaryItemSpecificationsIntegralFlowmeterRemoteFlowtubeIntegralFlowwmeterRemoteFlowtubeRemoteFlowtubeIntegralFlowmeterRemoteFlowtubeCodeAXF***G-DAXF***G-EAXF***G-NAXF***G-PAXF***C-DAXF***C-EAXF***C-NAXF***C-PAXF***W-NAXF***W-PAXF***H-DAXF***H-EAXF***H-NAXF***H-POil-prohibited Use withDehydrating TreatmentPainting Color ChangeEpoxy Resin CoatingHigh Anti-corrosionCoatingMaterial CertificateHydrostatic TestCalibration CertificateVent HoleEnhanced DualFrequency Excitation(*4)Electrodes, linings, and grounding rings are assembled and packed withpolyethylene including desiccants after being cleaned with water andacetone and dried with air. The label ‘OIL & WATER FREE’ is affixed.Coated in black (Munsell N1.5 or its equivalent.)Coated in jade green (Munsell 7.5 BG 4/1.5 or its equivalent.)Coated in metallic silver.Epoxy resin coating which has alkali-resistance instead of standardpolyurethane resin coating. The color is same as standard type.Three-layer coating (polyurethane coating on two-layer epoxy resincoating) in the same range as that for the standard coating. The color issame as standard type. Salt/alkali/acid/weather-resistance.Reproduced material certificates for :PFA/polyurethane: Pipe, electrodes, grounding rings/groundingelectrodes, flanges or mini flanges, adapters (for sanitary type)Ceramics: only grounding rings or grounding electrodesThe test verifies the absence of leaks by applying the following waterpressures (which are determined under process connection conditions) tolinings for ten minutes. Test results are described in the Note column of atest certificate (QIC).Process Connection:Water Pressure:ANSI Class 150, DIN PN10, JIS 10K1.5 MPaANSI Class 300, DIN PN16, JIS 20K3.0 MPaDIN PN40, Union joint (Ceramics lining)6.0 MPaJIS F121.25 MPaLevel 2: The Declaration and the Calibration Equipment List are issued.Level 3: The Declaration and the Primary Standard List are issued.Level 4: The Declaration and the Yokogawa Measuring Instruments ControlSystem are issued.With a vent hole provided for permeable fluids (such as nitric acid,hydrofluoric acid, or sodium hydroxide at high temperature).Available only for a PFA lining flange type tube.Available for 25 to 200 mm (1.0 to 8.0 in.) sizes.Products are delivered with the Standard dual frequency excitation modeand the Enhanced dual frequency excitation mode enabled.As flow calibration is not performed for optional code HF1 while inEnhanced dual frequency excitation. Excitation mode select optional codeHF2 when an accurate flow measurement is required.Available for 25 to 200 mm (1.0 to 8.0 in.) sizes.Products are delivered with the Standard dual frequency excitation modeand the Enhanced dual frequency excitation mode enabled.The meter factor for the Enhanced dual frequency excitation obtained byflow calibration is inscribed on the nameplate and set into the combinedconverter in addition to the meter factor for the Standard dual frequencyexcitation. – – – K5 – P1 – P2 – P7 – – – X1 – – – X2 M01 – – T01 L2 L3 L4 – – – H HF1 HF2T26-3.EPSAll Rights Reserved. Copyright © 2003, Yokogawa Electric Corporation GS 01E20D01-01E May 10,2006-00