Aspire PCPro/WebPro Installation Manual - Support - NEC Unified ...

More documents

Recommendations

Info

Connecting to the System - Remote Modem to Serial PortNull Modem Pin-OutSignal DB-25 Pin DB-9 Pin To DB-9 Pin DB-25 Pin SignalFG (Frame Ground) 1 - - 1 FGTD (Transmit Data) 2 3 2 3 RDRD (Receive Data) 3 2 3 2 TDRTS (Request to Send) 4 7 8 5 CTSCTS (Clear to Send) 5 8 7 4 RTSSG (Signal Ground) 7 5 5 7 SGDSR (Data Set Ready) 6 6 4 20 DTRCD (Carrier Detect) 8 1 4 20 DTRDTR (Data Terminal Ready) 20 4 1 8 CDDTR (Data Terminal Ready) 20 4 6 6 DSR4. Use a communication software (such as HyperTerminal) to connect to the Aspire S/Aspire serial port. Set the communicationsoftware to use the following settings:- Baud Rate: 19200(must match Aspire Program 10-21-02 setting)It is recommended to increase the baud rate to 38400 (the maximum rate for a serial connection).- Data Bits: 8- Parity: None- Stop Bits: 1- Flow Control: HardwareIf using HyperTerminal, start the program by clicking START - PROGRAMS - ACCESSORIES - COMMUNI-CATIONS - HYPERTERMINAL. Create a name for the new connection, such as MODEM SETUP and click OK.Select the COM Port to be used and click OK, set the RS232 options with the above settings, then click OK.5. Type AT then press Enter.Either OK or AT should appear to tell you that your cable connection and communication parameters areset correctly. If not, recheck your communication parameters set in Program 10-21-02, recheck the communicationsoftware parameters and check that the null modem cable is using the correct pin-out.6. Once the communication between the system and PC is established, the Aspire S/Aspire serial port needs to be modifiedwith the following entries. After each line, press the Enter key.ATR1AT&WThe screen should indicate a series of ATs. If not, repeat Step 6 until they appear.To reset this serial port to its initial setting, enter:ATR0AT&W7. Disconnect the HyperTerminal connection but do not close the HyperTerminal program. Disconnect the PC from theAspire S/Aspire system.8. Connect the NEC-recommended CNet modem model #CN5614XR (P/N 85862D) power supply to the modem, connectthe modem using a straight-through cable to the serial communication port of your computer, and turn on the modem.Check the manuals that came with your computer if you’re not sure how to set up and connect a modem toyour computer.12 ◆
Connecting to the System - Remote Modem to Serial PortSend and store the INIT string in the site modem:1. Type AT&F and press Enter to default the modem.OK will display on the screen. If OK does not appear, press Enter, type AT&F and press Enter again. If OKstill does not appear, there is a problem with the connection between the computer and mode. Correct the problembefore repeating this step.2. Enter the following initialization string:AT&D3 and press Enter.ATS0=2 and press Enter.AT&C0 and press Enter.AT&W0 and press Enter.AT&W1 and press Enter.3. To view all the modem settings and check the INIT string, typeAT&V and press Enter.The INIT string you sent in step 2 is contained in the data that displays. Review the displayed Active Profile,Stored Profile 0 and Stored Profile 1 data to be sure your entries were correct. (Not all types of modems are compatiblewith all these commands and will disregard the entries for some items.) The entries of &C0, S00:002 and&D3 should appear in the active and stored profiles. If not, repeat Steps 1-3.4. Close the HyperTerminal Program. You do not need to save the modem file created.5. Turn off the modem and disconnect it from the PC.Connecting the site modem to the Aspire S/Aspire system:1. Connect the modem to the Aspire S/Aspire system using a straight-through cable.2. Turn the modem on.3. Determine how you wish to communicate with the modem connected to the system and make the proper connections.Some of the possible connections to the remote modem which may be done are:● Using a direct line connected to the modem● Through a DISA line along with a single line port connected to the modem● Through Voice Mail/Automated Attendant along with a single line port connected to the modem● Through a line directly terminated to a single line port connected to the modem● Through a normal line to have a person answer the incoming call and transfer you to the singleline extension number connected to the modem.4. Continue with Direct Dial Up (modem connection via serial cable to Aspire S/Aspire cabinet) on page 31.◆ 13
Page 2 and 3: This manual has been developed by N
Page 4 and 5: Using PCPro . . . . . . . . . . . .
Page 7 and 8: Aspire Software and PCPro Compatibi
Page 9 and 10: Connecting to the Aspire S/Aspire S
Page 11 and 12: Connecting to the Aspire S/Aspire S
Page 13 and 14: Installing PCPro6. Change the insta
Page 15: Connecting to the System - Remote M
Page 19 and 20: Connecting to the System - Local Se
Page 21 and 22: 6. The software continues the insta
Page 23 and 24: Connecting to the System - LAN (Eth
Page 25 and 26: Connecting to the System - LAN (Eth
Page 27 and 28: Creating a Dial Up SettingCreating
Page 29 and 30: 6. The DIAL-UP CONNECTION bullet sh
Page 31 and 32: Direct Dial Up (direct serial cable
Page 33 and 34: Creating a Dial Up Setting10. Windo
Page 35 and 36: Creating a Dial Up SettingDirect Di
Page 37 and 38: Creating a Dial Up Setting10. Windo
Page 39 and 40: Creating a Dial Up SettingCompletin
Page 41 and 42: Creating a Dial Up Setting7. In the
Page 43 and 44: Creating a Dial Up Setting12. Click
Page 45 and 46: Creating a Dial Up Setting20. Selec
Page 47 and 48: Using PCProUsing PCProUsing PCProSe
Page 49 and 50: Using PCProUsing PCProTo create a n
Page 51 and 52: Using WebProUsing WebProUsing WebPr
Page 53 and 54: Using WebPro8. Once the User Name a
Page 55 and 56: PCPro/WebPro FeaturesPCPro/WebPro F
Page 57 and 58: PCPro/WebPro FeaturesProgrammingSys
Page 59 and 60: PCPro/WebPro FeaturesOtherHelpClick
Page 61 and 62: Troubleshooting Your ConnectionTrou
Page 63 and 64: Troubleshooting Your Connection13.
Page 65 and 66: NEC Unified Solutions, Inc.4 Forest

Aspire PCPro/WebPro Installation Manual - Support - NEC Unified ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?