Altistart 22 - Schneider Electric

More documents

Recommendations

Info

Remote keypad display - optionThe VW3G22101 remote keypad IP54 or VW3G22102 remote keypad IP65 can be mounted on the door of the wall-mounted or floorstandingenclosure with a seal which offers IP65 protection. Any display restrictions applied to the soft starter by the remote terminal switchwill still be in force once the soft starter has been disconnected and even after it has been switched off.Note: Set the remote keypad with• Modbus rate = 19.2 Kbps, (see tbr)• Modbus format = 8E1, 8 bit, even parity, 1 stop bit (see For)1L1 3L2 5L3RdyComRunTripRJ45connector2T1 4T2 6T3RJ45connectorCable VW3A1104Rpp (pp = 10 or 30)44 BBV51330 08/2012
ProgrammingProgramming and setupPreliminary recommendationsLOSS OF CONTROLWARNING• The designer of any control scheme must- consider the potential failure modes of control paths and, for certain critical control functions,- provide a means to achieve a safe state during and after a path failure.Examples of critical control functions are emergency stop and overtravel stop.• Separate or redundant control paths must be provided for critical control functions.• System control paths may include communication links. Consideration must be given to the implications of unanticipatedtransmission delays or failures of the link. (1)• Each implementation of an ATS22 soft starter must be individually and thoroughly tested for proper operation before being placedinto service.Failure to follow these instructions can result in death, serious injury, or equipment damage.(1)For additional information, refer to NEMA ICS 1.1 (latest edition), “Safety Guidelines for the Application, Installation, and Maintenanceof Solid State Control”.When changing the factory configuration, record your parameter settings in the Parameter Index and Modbus addresses table, startingpage 77.BBV51330 08/2012 45
Page 1: 2354235 11/2008Altistart 22Soft sta
Page 6 and 7: Documentation structureThe followin
Page 8 and 9: Receiving and handlingIntroductionT
Page 10 and 11: SelectionTorque characteristicTs an
Page 12 and 13: SelectionStandard application, Alti
Page 14 and 15: Dimensions and weightsATS22D17 to D
Page 16 and 17: Dimensions and weightsATS22C21 to C
Page 18 and 19: MountingSoft starter ventilationOn
Page 20 and 21: Mounting - Fan optionFan for frame
Page 22 and 23: Thermal protectionSoft starter ther
Page 24 and 25: Thermal protectionWarm curvest (s)C
Page 26 and 27: WiringInstallation PrecautionsDANGE
Page 28 and 29: WiringRefer to application diagrams
Page 30 and 31: WiringThe ATS22pppQ range (230-440
Page 32 and 33: Wiring - power terminalsPowerObserv
Page 34 and 35: Wiring - power terminalsPower conne
Page 36 and 37: Wiring - control terminalsElectrica
Page 38 and 39: Wiring - in line connection - appli
Page 40 and 41: Wiring - in line connection - appli
Page 42 and 43: Display terminalFunctions of the ke
Page 46 and 47: ProgrammingMenu structureTwo menu l
Page 48 and 49: List of parametersParameters access
Page 50 and 51: Configuration menu (ConF)conFCode N
Page 52 and 53: Settings menu (SEt)Code Name/Descri
Page 54 and 55: Advanced adjustments menu (AdJ)Code
Page 56 and 57: Advanced protections menu (PrO)Code
Page 58 and 59: Advanced protections menu (PrO)Code
Page 60 and 61: Advanced IO menu (IO)Code Name/Desc
Page 62 and 63: Advanced communication menu (COP)Co
Page 64 and 65: Utility menu (UtIL)Code Name/Descri
Page 66 and 67: Command channelBehavior on channel
Page 68 and 69: Modbus FunctionThis section describ
Page 70 and 71: Modbus FunctionWrite one output wor
Page 72 and 73: Modbus FunctionError managementExce
Page 74 and 75: MaintenanceServicingIt is advisable
Page 76 and 77: Diagnostics / TroubleshootingTrip c
Page 78 and 79: Parameter Index and Modbus addresse
Page 80 and 81: Parameter Index and Modbus addresse
Page 82 and 83: Annex 1: UL508 schematicsATS22•
Page 84 and 85: 84 BBV51330 08/2012

Altistart 22 - Schneider Electric

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?