Owner's Manual - Hearth & Home Technologies

More documents

Recommendations

Info

K. Slim Line Wall ThimbleBefore you begin review the venting confi gurations in FiguresA, B and C on the next page.Assembling Slim Line Trim Ring and Heat ShieldFigure 5.33 Attach the heat shield to the trim ring withthe four screws provided. Screws go through the heatshield and into the brackets on the trim ring.Figure 5.31 Lay the trim ring on fl at surface and bend upthe six welded brackets into a 90 degree position. Thebrackets along the outer edge of the ring are for locatingthe ring in the center of the hole.Installing Slim Line Trim Ring and Heat ShieldMeasure from the fl oor to the center of the vent pipe. Cutout a 9-1/2 in. (241 mm) hole in the wall. Hold the trimring/heat shield assembly in place and put a mark on theshield with a black marker where it protrudes through theexterior wall. See Figure A on the next page.Use that mark as a guide to trim off excess heat shieldwith a pair of sheet metal shears.3/4 3/4 3/4Figure 5.32 The heat shield is shipped fl at and must behand bent into a half circle before attaching it to the trimring. Bend the heat shield as shown.CAUTIONSharp Edges• Wear protective gloves and safetyglasses during installation.Figure 5.34 When installing the trim ring/heat shieldassembly make sure the trim ring is centered in the holeand that the shield is above the pipe. There must be aminimum of 3/4 in. (19 mm) minimum clearance maintainedto combustibles from the top of the heat shield.Ensure that framing on the inside of the wall is a minimuminner framing diameter of 10 in. x 10. in. (254 mmx 254 mm).The four trim ring mounting screws provided should bereplaced with appropriate fasteners for stucco, brick, concrete,or other types of sidings.24Heat & Glo • Paloma • 7031-220 Rev. S • 8/09
FIG. A 90 DEGREE ELBOWPLACE MARK WHERE PROTRUDES THROUGHEXTERIOR WALL TO CUT OFF EXCESS90° ELBOWUSE HEAT SHIELD / WALL THIMBLECENTER LINEPIPE LENGTHTRIM RINGPIPE LENGTHHTI VENT HHW2 PART #841-0670(RECOMMENDED FOR OPTIMUM PERFORMANCE)FIG. B 45 DEGREE ELBOWTRIM RING45° ELBOWHEAT SHIELDOVER PIPE5 IN. (127 MM) CLEARANCEFROM APPLIANCE CORNERTO COMBUSTIBLE WALLFIG. C MINIMUM CLEARANCE5 IN. (127 MM) CLEARANCEFROM APPLIANCE CORNERINTERIOR WALL - 2 IN. (51MM) CLEARANCE FROMREAR OF STOVEMINIMUM OF 6 IN. (152 MM)OF PIPE THROUGH THE WALLWALL THIMBLECENTER LINEHEAT SHIELD OVERTOP HALF OF PIPEHTI VENT HHW2 PART#841-0670 (RECOMMENDEDFOR OPTIMUM PERFORMANCE)TRIM RINGSnorkel Cap Kit (SLK-SNKD) must be used for horizontal vent runs with no vertical rise.Figure 5.35Heat & Glo • Paloma • 7031-220 Rev. S • 8/09 25
Page 1 and 2: Owner’s ManualInstallation and Op
Page 3: Table of Contents1 Listing and Code
Page 6 and 7: 2GettingStartedA. Design and Instal
Page 8 and 9: C. Optional Stone Surround Installe
Page 10 and 11: MNRPQ(See Note 2)VTVSElectricalServ
Page 12 and 13: D. How to Use the Vent Graph1. Meas
Page 14 and 15: WOODSCREWCENTER OF HOLECENTER LINEW
Page 16 and 17: G. Vertical TerminationVERTICAL TER
Page 18 and 19: 9. Twist-lock the vent cap and seal
Page 20 and 21: I. Class A Metal ChimneyTERMINATION
Page 22 and 23: CAUTIONCUT AND BEND FLASHINGAS NEED
Page 26 and 27: 6Gas InformationA. Fuel Conversions
Page 28 and 29: 21. Place one piece grommet over pi
Page 30 and 31: 7Electrical InformationA. Recommend
Page 32 and 33: E. Wall Switch Installation for Fan
Page 34 and 35: C. Leveling and Lagging Down the Ap
Page 36 and 37: 9. Install the cover plate removed
Page 38 and 39: J. Mineral WoolWARNINGExplosion Ris
Page 40 and 41: Attach the ground clip to the contr
Page 42 and 43: L. Remote ControlsTools Required: P
Page 44 and 45: M. Front Door Glass Assembly Instal
Page 46 and 47: C. Lighting ApplianceIPI IgnitionFO
Page 48 and 49: 10 TroubleshootingWith proper insta
Page 50 and 51: 11Maintaining and Servicing Applian
Page 52 and 53: 12Reference MaterialsA. Appliance D
Page 54 and 55: C. Vent Components Diagram6-1/2 in.
Page 56 and 57: . Limite Lietime nt60Heat & Glo
Page 58: . Contt InomtionHeat & Glo, a brand

Owner's Manual - Hearth & Home Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?