Owner's Manual - Hearth & Home Technologies

More documents

Recommendations

Info

2GettingStartedA. Design and Installation Considerations C. Inspect Appliance and ComponentsHeat & Glo direct vent gas appliances are designed tooperate with all combustion air siphoned from outside ofthe building and all exhaust gases expelled to the outside.No additional outside air source is required.CAUTIONCheck building codes prior to installation.• Installation MUST comply with local, regional, state andnational codes and regulations.• Consult local building, fire officials or authorities having jurisdictionabout restrictions, installation inspection, and permits.When planning an appliance installation, it’s necessary todetermine the following information before installing:• Where the appliance is to be installed.• The vent system confi guration to be used.• Gas supply piping.• Electrical wiring.• Framing and fi nishing details.• Whether optional accessories—devices such as a fan,wall switch, or remote control—are desired.WARNINGInspect appliance and components for damage.Damaged parts may impair safe operation.• Do NOT install damaged components.• Do NOT install incomplete components.• Do NOT install substitute components.Report damaged parts to dealer.• Carefully remove the appliance and components fromthe packaging.• Remove door and set aside on protective surface. Seepage 44.• Remove log set and component pack from fi rebox.• Report to your dealer any parts damaged in shipment,particularly the condition of the glass.• Read all of the instructions before starting the installation.Follow these instructions carefully during theinstallation to ensure maximum safety and benefit.WARNINGHearth & Home Technologies disclaims anyWARNINGresponsibility for, and the warranty will be voidedby, the following actions:Keep appliance dry.• Installation and use of any damaged appliance or ventsystem component.• Mold or rust may cause odors.• Modifi cation of the appliance or vent system.• Water may damage controls.• Installation other than as instructed by Hearth & HomeTechnologies.B. Tools and Supplies Needed• Improper positioning of the gas logs or the glass door.• Installation and/or use of any component part not approvedBefore beginning the installation be sure that the followingby Hearth & Home Technologies.tools and building supplies are available.Any such action may cause a fire hazard.Reciprocating saw Framing materialPliersHi temp caulking materialHammerGlovesPhillips screwdriver Framing squareFlat blade screwdriver Electric drill and bits (1/4 in.)Plumb lineSafety glassesLevelWrenchesRatchets/Sockets Allen Wrench SetManometerVoltmeterTape measure 1/2 - 3/4 inch length, #6 or #8 Self-drilling screwsOne 1/4 inch female connection (for optional fan)Noncorrosive leak check solution or combustible gas detector6Heat & Glo • Paloma • 7031-220 Rev. S • 8/09
3Framingand ClearancesNote:• Illustrations reflect typical installations and are FORDESIGN PURPOSES ONLY.• Illustrations/diagrams are not drawn to scale.• Actual installation may vary due to individual designpreference.A. Selecting Appliance LocationWhen selecting a location for your appliance it is important toconsider the required clearances to walls (see figure 3.1).WARNINGFire RiskProvide adequate clearance:• Around air openings• To combustibles• For service accessLocate appliance away from traffi c areas.NOTE: For actual appliance dimensions refer to Section12.B. Clearances to CombustiblesFBIKCAEKJC“A” MEASUREMENT IS FROM APPLIANCE TOP, NOT SIDEALCOVEGHAADModel A B C D E F G H I J KPalomaInches 6 10-1/8 12-1/8 54 36 30-3/4 13-1/4 13-1/4 1 15-1/2 5Millimeters 152 257 308 1372 914 781 337 337 25 394 127Figure 3.1Heat & Glo • Paloma • 7031-220 Rev. S • 8/09 7
Page 1 and 2: Owner’s ManualInstallation and Op
Page 3: Table of Contents1 Listing and Code
Page 8 and 9: C. Optional Stone Surround Installe
Page 10 and 11: MNRPQ(See Note 2)VTVSElectricalServ
Page 12 and 13: D. How to Use the Vent Graph1. Meas
Page 14 and 15: WOODSCREWCENTER OF HOLECENTER LINEW
Page 16 and 17: G. Vertical TerminationVERTICAL TER
Page 18 and 19: 9. Twist-lock the vent cap and seal
Page 20 and 21: I. Class A Metal ChimneyTERMINATION
Page 22 and 23: CAUTIONCUT AND BEND FLASHINGAS NEED
Page 24 and 25: K. Slim Line Wall ThimbleBefore you
Page 26 and 27: 6Gas InformationA. Fuel Conversions
Page 28 and 29: 21. Place one piece grommet over pi
Page 30 and 31: 7Electrical InformationA. Recommend
Page 32 and 33: E. Wall Switch Installation for Fan
Page 34 and 35: C. Leveling and Lagging Down the Ap
Page 36 and 37: 9. Install the cover plate removed
Page 38 and 39: J. Mineral WoolWARNINGExplosion Ris
Page 40 and 41: Attach the ground clip to the contr
Page 42 and 43: L. Remote ControlsTools Required: P
Page 44 and 45: M. Front Door Glass Assembly Instal
Page 46 and 47: C. Lighting ApplianceIPI IgnitionFO
Page 48 and 49: 10 TroubleshootingWith proper insta
Page 50 and 51: 11Maintaining and Servicing Applian
Page 52 and 53: 12Reference MaterialsA. Appliance D
Page 54 and 55: C. Vent Components Diagram6-1/2 in.
Page 56 and 57:
. Limite Lietime nt60Heat & Glo
Page 58:
. Contt InomtionHeat & Glo, a brand
show all

Owner's Manual - Hearth & Home Technologies

Create successful ePaper yourself

Delete template?

Save as template?