BRC Series System Guide - Sony

More documents

Recommendations

Info

BRC-Z700BRC-Z330MODE settingFunction ofVALUE controlFunction ofBRIGHT controlMODE settingFunction ofVALUE controlFunction ofBRIGHT controlFULL AUTONot usedExposure compensationlevel control*FULL AUTONot usedExposure compensationlevel control*SHUTTER Shutter speed Exposure compensationPriority control level control*IRIS F-number Exposure compensationPriority control level control*GAIN Gain Exposure compensationPriority control level control*SHUTTER Shutter speed Exposure compensationPriority control level control*IRIS F-number Exposure compensationPriority control level control*GAIN Gain Exposure compensationPriority control level control*MANUALShutter speedcontrol•F-number and gaincontrols (when the DIPswitch 3 at the bottom ofthe Remote Control Unit isset to ON)•F-number control (whenthe DIP switch 3 at thebottom of the RemoteControl Unit is set to OFF)MANUALShutter speedcontrol•F-number and gaincontrols (when the DIPswitch 3 at the bottom ofthe Remote Control Unit isset to ON)•F-number control (whenthe DIP switch 3 at thebottom of the RemoteControl Unit is set to OFF)* When EX-COMP is ON in the EXPOSURE menu. * When EX-COMP is ON in the EXPOSURE menu.BRC-300/300PMODE settingFULL AUTOFunction ofVALUE controlNot usedFunction ofBRIGHT controlExposure compensationlevel control*SHUTTER Shutter speed Exposure compensationPriority control level control*IRISPriorityIris controlExposure compensationlevel control*BRIGHT Not used Brightness level controlMANUALShutter speedIris controlcontrol* When EX-COMP is ON in the EXPOSURE menu.30 Remote Operation
Storing the Camera Setting inMemoryStoring camera settings:Memory Preset featureTo store the camera settings4RESETLights for positions 1 to 8.Lights for positions 9 to 16.4 211 Press the CAMERA button to select the requiredcamera.2 Press the PAN/TILT RESET button to reset the pan/tilt position.3 Adjust the position, zooming, focusing, andbacklighting of the selected camera.4 While holding down the PRESET button (forpositions 1 to 8) or the SHIFT and PRESET buttons(for positions 9 to 16), press any of the POSITIONbuttons in which you want to store settings.While holding down (for POSITION 1 to 8)Press a POSITION button.While holding down (for POSITION 9 to 16)Settings are stored in the memory of the camera.The pressed button flashes during storing. Flashingstops when storing is completed.To recall the stored settingsPress any of the POSITION buttons in which youhave stored the settings. For positions 9 to 16, holddown the SHIFT button and press any of thePOSITION buttons.To cancel the preset memoryWhile holding down the RESET button (for positions1 to 8) or the SHIFT and RESET buttons (for positions9 to 16), press the POSITION button from which youwant to cancel the settings.The pressed button flashes while settings arebeing cancelled. Flashing stops when thesettings have been canceled.NoteWhile holding down (for POSITION 1 to 8)Press a POSITION button.While holding down (for POSITION 9 to 16)Important note:• When the power is turned on, the camera startswith the settings stored in POSITION 1.• If you want to retain the previous pan and tiltposition when the power is turned off and turnedon again, store those positions in POSITION 1.• When you are storing or canceling the settings inone position, you cannot call up, store or cancelthe settings in another position.Setting the speed of the cameramoving to a preset positionYou can select the panning/tilting speed whenthe camera moves to a preset position.1 Press the CAMERA button to select the requiredcamera.2 Press the POSITION button for which you want toset the speed for more than one second. All ofthe CAMERA buttons, 1 to 7, flash.3 Press one of the CAMERA buttons to select thespeed.CAMERA button1 1 degree/sec.Panning/tilting speed2 2.2 degree/sec.3 4.8 degree/sec.4 11 degree/sec.5 23.3 degree/sec.6 43 degree/sec.7 60 degrees/sec. (default)Now the camera will move to the position presetto the pressed POSITION button with the selectedspeed.To set the speed of the camera moving to apreset position between 9 and 16Hold down the SHIFT button and press thecorresponding POSITION button for more than onesecond. The POSITION 1 to 8 buttons can be usedfor positions 9 to 16.Remote Operation31
Page 2: 2 Using the BRC-H700/BRC-Z700 as a
Page 8 and 9: 3Key FeaturesAll-in-one P/T/Z Desig
Page 10 and 11: Other FeaturesFlexible installation
Page 12 and 13: BRC and BRU SystemBRC-H700 BRC-Z700
Page 14 and 15: OFFOFFONONRSetting of the BOTTOM sw
Page 16 and 17: 5.1.3 BRC-Z330Rear1 2 3 4 5 6 7Pin
Page 18 and 19: Bottom12 13 142Switch 2 (RS-232C/RS
Page 20 and 21: 10 VISCA RS-232C OUT connector11 CA
Page 22 and 23: 5.3.8 BRBK-HD2 HD-SDI OutputCard15.
Page 24 and 25: 7Remote Operation7.1 IR Remote Comm
Page 26 and 27: Improved functionality with theRM-B
Page 28 and 29: JoystickMovement of thecameraSettin
Page 32 and 33: Preset memoryPreset Memory 1: All o
Page 34 and 35: 7 8 94 5 61 2 30 .CAMCAMERADSK/AUXP
Page 36 and 37: 9Operation with the AWS-G500 Series
Page 38 and 39: 9.3 Operating the PGM and NEXT Sele
Page 40: 11 SpecificationsBRC-H700 BRC-Z700
Page 44 and 45: BRU-H700TopSide210 (8 3/8) 86 (3 1/
Page 46 and 47: Ceiling Bracket (B) for BRC-Z33012
Page 48 and 49: 13.4 Estimated Viewing Angle of BRC
Page 50 and 51: Estimated Viewing Angle (width)BRC-
Page 52 and 53: Estimated Viewing Angle (width)BRC-
Page 54 and 55: 13.8 Function priorityThis table sh
Page 57 and 58: 13.11.2 Wiring Diagram of VISCA RS-
Page 59 and 60: 14Installing the Camera in a High P
Page 61 and 62: 9 Connect the cables to the connect
Page 63 and 64: 8 Connect the cables to the connect
Page 66: Distributed by© 2008 Sony Corporat

BRC Series System Guide - Sony

Create successful ePaper yourself

Delete template?

Save as template?