Mobrey

More documents

Recommendations

Info

MAIN MENU SUB MENU 1 SUB MENU 2 PARAMETER DESCRIPTION Par No.SETUP (Contd)ALARM Memory Fault Alarm P540PV Out of LimitsP541Current SaturatedP542Temperature Out of Limits P543Logging Memory FillingP544Digital Input 1 ActiveP545DISPLAY Display Select 1 (upper) P570Display Select 2P571Display Select 3P572Backlight On/OffP575LOGGING Interval P590Fast Log SelectP591Overwrite OldP592ENGINEERING Frequency P630(setup) SENSOR LIMITS Min dB P640Max dBP641Sensor Dirty ThresholdP642SYSTEM TEST CURRENT OUTPUT 4mA output adjust 1 P70020mA output adjust 1P701Set Current 1P702SETTINGS Date P730TimeP731Keypad Sound On/OffP735FIXED Model Code D750Serial NumberD751Hardware VersionD752Software RevisionD753HART Manufacturer’s Code D760Unique IDD761Universal Command Rev D762TS Command RevD763Preamble BytesD764FlagsD765MONITOR READINGS PV(process variable) D800SV (Sludge Density)D801% Current Output 1 D805Current Output 1D806TotaliserD810RELAYRELAY RUN TIMES Relay 1 Run TimeD821Relay 2 Run TimeD822ALARM REPORTD830DIAGNOSTICS Digital input status D835TemperatureD844Sensor Attenuation @ 1MHz D850Attenuation @ 3.3MHzD851Attenuation unsmoothed D852Signal level (Raw A/D bits) D853Span Average @ 1MHzD854Span Average @ 3.3MHz D855Sample Average @ 1MHz D856Sample Average @ 3.3MHz D857Slope 1D858Slope 3D859Frequency of operationD860Max. density measurable D86132IP258
APPENDIX A2: FULL LIST OF FUNCTIONSParameter list and descriptionP=Parameter, D=Diagnostic Display ParameterParameter Description Min Max DefaultNo. value value Ex-FactoryP100 Sensor Gap in mm.This is a user entered parameter (optional).This value is ignored when an alternative spancalibration is caried out (i.e. method two or three). 0 1000 0.0P101 Sludge typeThe user can select from a list of sludge type to setup the span for the calibration procedure (optional).Each sludge type is associated with an attenuationfactor for each frequency. This value is ignored whenan alternative span calibration is caried out(i.e. method two or three). - - noneP102 dB Factor @ 1MHzA user alterable parameter. This is the attenuationnumber in dB/% at 1MHz. This is used for the spancalibration (method three). 0 - 0.000P103 dB Factor @ 3.3MHzA user alterable parameter. This is the attenuationnumber in dB/% at 3.3MHz.This is used for the spancalibration (method three). 0 - 0.000P120 Zero Ref @ 1MHzThis is the value in dBs (@ 1MHz) that is stored inthe control unit when a zero calibration is carried out.This value is over written each time a zero calibrationis carried out. - - 16P121 Zero Ref @ 3.3MHzThis is the value in dBs (@ 3.3MHz) that is stored inthe control unit when a zero calibration is carried out.This value is over written each time a zero calibrationis carried out. - - 16P122 Date of Zero RefThis is automatically stored by the control unit whenthe zero calibration is done. The actual date can beset-up in the ENGINEER menu (P730) - - --/--/----P123 Initial Zero Ref @ 1MHz dB’sThis is the value in dBs (@ 1MHz) that is stored inthe control unit when the initial zero calibration iscarried out.This value is compared with subsequentzero calibrations.0 must be entered to reset or clear initialzero value - - 0P124 Initial Zero Ref @ 3.3MHz dB’sThis is the value in dBs (@ 3.3MHz) that is stored inthe control unit when the initial zero calibration iscarried out.This value is compared with subsequentzero calibrations.0 must be entered to reset or clear initial33IP258
Page 1 and 2: Instruction LeafletIP258November 20
Page 3 and 4: Safety PrecautionsThe following saf
Page 5 and 6: 1.0 PRODUCT INTRODUCTION1.1 THE MSM
Page 7 and 8: 2.0 SENSOR TYPES2.1 SUSPENDED SENSO
Page 9 and 10: 3.0 CONTROL UNIT3.1 MSM400 DISPLAYS
Page 11 and 12: 4 INSTALLATION4.1 PRELIMINARY CHECK
Page 13 and 14: 4.6 ELECTRICAL CONNECTIONSAll field
Page 15 and 16: TRIGGER INPUTSThere is trigger inpu
Page 17 and 18: 3. Use the down arrow key (ß) to h
Page 19 and 20: 6.2 RECHECKING ZEROIt is recommende
Page 21 and 22: After a few secnds the display will
Page 23 and 24: Under stable operating conditions,
Page 25 and 26: Starting desludgeThis is controlled
Page 27 and 28: 7.1 OUTPUTS7.2 CURRENT OUTPUTThe op
Page 29 and 30: The display has a backlight, which
Page 31: FULL MENU STRUCTURE - LOCATION OF P
Page 35 and 36: Parameter Description Min. Max. Def
Page 37 and 38: Parameter Description Min. Max. Def
Page 39 and 40: 2.0 SMART COMMUNICATION WITH THE MO
Page 41 and 42: D. HANDHELD COMMUNICATOR - MOBREY -
Page 43 and 44: Fig D1 : MOBREY-CK* HHC assembly43I
Page 45 and 46: D.5.0. Hand Held Communicator : Ope
Page 47 and 48: When an MSM400 Control unit is loca
Page 49 and 50: D7.1 Monitor/Display Parameters - D
Page 51 and 52: HAND HELD COMMUNICATOR REGISTERSD9.
Page 53 and 54: D.9.1 Printout or PC transfer of MS
Page 55 and 56: “PASSWORD NOT OPEN”- If the Pas
Page 57 and 58: (pre change) value : this prompts t
Page 59 and 60: D13.0 SMART Interfaces - Compatibil

Mobrey

Create successful ePaper yourself

Delete template?

Save as template?