ES721 ISO40 7 kW NL - HSD

More documents

Recommendations

Info

<strong>HSD</strong> 9.8 PNEUMATIC CONNECTIONS i See the figures in paragraph 8.1 for the location and sizes of connections. See paragraph 7.1 for air consumptions. 9.9 EXAMPLE OF COMPRESSED AIR CIRCUITS 9.9.1 Tool-holder changing circuit electrospindle cilinder ( S ) ( R ) 5-2 monostable valve The cylinder of this electrospindle is single-acting. 4 2 1 5 3 hoses : Ø 8x6 Minimum two step air-cleaning kit step 1 : 5 μm filter step 2 : 0,1 μm oil remover If not supplied is advisable to insert a security valve with open at 2.5/3 Bar between the cylinder and 5-2 monostable valve. 9.9.2 Pressurization circuit pressione 4 Bar pressure regulator hoses : Ø 6x4 Minimum ( P ) 6 Bar Pressurization inlet pressure switch 4 Bar two step air-cleaning kit step 1 : 5 μm filter step 2 : 0,1 μm oil remover The internal pressurisation pneumatic circuit prevents harmful particles from entering the electrospindle. 5801H0066 en Rev.01 24/48 6 Bar The pressurisation air must be present even when the electrospindle is at a standstill and the machine is switched on. It must be present also when cleaning or servicing the machinery, to prevent dust from other machining areas entering the spindle. Check with the spindle at standstill that there is a uniform outlet of air around the spindle shaft (pressurisation); if this is not the case, check the efficiency of the pneumatic circuit and the tightness of the connections.
<strong>HSD</strong> 9.10 AUTOMATIC CONE CLEANING 1. 6 bar air inlet 1 2. water inlet for internal tool cooling 3. to be connected to the “water to the tool” inlet (see paragraph 8.1 ) ( T ) 3 2 Figure aside shows an example of a compressed air circuit for automatic cone cleaning. During the tool change phase, water delivery is stopped and compressed air is delivered instead to blow out any dirt which may have built up. (NOTE: The cone must still be checked and cleaned on a regular basis as instructed in section § 11 on spindle maintenance). 5801H0066 en Rev.01 25/48
Page 1 and 2: HSD MECHATRONIC D I V I S I O N HSD
Page 3 and 4: HSD 10.7.2 Electrospindle states an
Page 5 and 6: HSD § 4 TERMS OF WARRANTY HSD S.p.
Page 7 and 8: HSD 5.3 RISKS ASSOCIATED WITH THE E
Page 9 and 10: HSD § 6 TRANSPORT, PACKAGING, UNPA
Page 11 and 12: HSD § 7 TECHNICAL SPECIFICATIONS 7
Page 13 and 14: HSD § 8 DIMENSIONS AND MAIN PARTS
Page 15 and 16: HSD 8.1.2 Direct liquid coolant cou
Page 17 and 18: HSD 8.1.3 Deublin distributor, enco
Page 19 and 20: HSD § 9 INSTALLAZIONE HSD S.p.a. d
Page 21 and 22: HSD DPC 5801H0066 en Rev.01 21/48 !
Page 23: HSD 9.7 COMPRESSED AIR SPECIFICATIO
Page 27 and 28: HSD § 10 OPERATION 10.1 GENERAL PR
Page 29 and 30: HSD 10.7.2 Electrospindle states an
Page 31 and 32: HSD 10.10 CHOICE OF TOOLHOLDER CONE
Page 33 and 34: HSD 1 2 3 4 5 6 UTENSILE BLOCCATO U
Page 35 and 36: HSD 11.1 DAILY MAINTENANCE 11.1.1 C
Page 37 and 38: HSD § 12 REPLACEMENT OF COMPONENTS
Page 39 and 40: HSD 12.1.2 Replacement and adjustme
Page 41 and 42: HSD 12.1.5 Sensor S5 adjustment Aft
Page 43 and 44: HSD § 14 LIST OF SPARE PARTS CODE
Page 45 and 46: HSD The tool holder is not locked:
Page 47 and 48: HSD § 16 DECLARATION OF INCORPORAT

ES721 ISO40 7 kW NL - HSD

Create successful ePaper yourself

Delete template?

Save as template?