ES721 ISO40 7 kW NL - HSD

More documents

Recommendations

Info

HSD 5.5 RISKS SPECIFIC TO MAINTENANCE � Take great care not to cut yourself on the tools while servicing or cleaning the electrospindle. Ideally, tools should be removed prior to these operations. � Rotating parts may continue to spin under the effect of inertia even when the electrospindle has been switched off. Make absolutely sure that the spindle is not spinning before accessing it. � Perform all scheduled maintenance as described in this manual. Failure to do so may lead to mechanical failures and breakage through wear or inadequate maintenance. WARNING! � Make absolutely sure that the tool in the electrospindle has stopped rotating before commencing any maintenance operation! � Disconnect the electrospindle from the mains power supply before commencing any maintenance operation! � It is strictly forbidden to clean the electrospindle while it is functioning! 5801H0066 en Rev.01 8/48
HSD § 6 TRANSPORT, PACKAGING, UNPACKING, STORAGE 6.1 WARNINGS � The lifting and handling of the product may create hazardous situations for the persons involved; we therefore recommend that the instructions given by HSD S.p.A. are observed and that only suitable tools are used. � The erection and installation operations must always be carried out only by specialised technicians. � We recommend that all lifting and handling operations of the product or its parts be carried out with great care, avoiding collisions that could compromise the proper function or damage coated parts. The responsibility for selecting the most suitable lifting equipment (ropes, straps or chains, etc.) lies with the user, paying attention to safety and functionality such as lifting capacity, relative to the weight indicated on the packaging and on the label of the product. 6.2 DIMENSIONS AND WEIGHTS � Weight of the packed product: is indicated on the packaging. � Linear dimensions of the packed product: are indicated on the documents accompanying the product. 6.3 TRANSPORT AND PACKAGING CONDITIONS 6.4 UNPACKING PROCEDURE The product is shipped protected by a covering of VCI plastic and expanded foam, packed in a wooden crate or case of special cardboard. The figure below shows a few methods of lifting the packed product (using ropes and using a fork-lift truck; in the latter case, ensure that during lifting the centre of gravity of the crate is always between the two forks). The examples shown are only indications as it is not possible to determine in advance all the possible configurations with which it is possible to lift a product manufactured by HSD S.p.A.. Check the integrity of the seals on the packaging before opening the packaging If the product is packed in a wooden crate, insert a screwdriver under the locking hook. Open the hook, paying attention not to damage the packaging and its contents. If the product is packed in a cardboard case, remove the strip of adhesive tape, paying attention not to damage the packaging and its contents. Do not lift the product by pulling on the part of the electric fan, in order not to damage the guard. i The expanded foam and plastic cover can be disposed of as plastic material. 5801H0066 en Rev.01 9/48
Page 1 and 2: HSD MECHATRONIC D I V I S I O N HSD
Page 3 and 4: HSD 10.7.2 Electrospindle states an
Page 5 and 6: HSD § 4 TERMS OF WARRANTY HSD S.p.
Page 7: HSD 5.3 RISKS ASSOCIATED WITH THE E
Page 11 and 12: HSD § 7 TECHNICAL SPECIFICATIONS 7
Page 13 and 14: HSD § 8 DIMENSIONS AND MAIN PARTS
Page 15 and 16: HSD 8.1.2 Direct liquid coolant cou
Page 17 and 18: HSD 8.1.3 Deublin distributor, enco
Page 19 and 20: HSD § 9 INSTALLAZIONE HSD S.p.a. d
Page 21 and 22: HSD DPC 5801H0066 en Rev.01 21/48 !
Page 23 and 24: HSD 9.7 COMPRESSED AIR SPECIFICATIO
Page 25 and 26: HSD 9.10 AUTOMATIC CONE CLEANING 1.
Page 27 and 28: HSD § 10 OPERATION 10.1 GENERAL PR
Page 29 and 30: HSD 10.7.2 Electrospindle states an
Page 31 and 32: HSD 10.10 CHOICE OF TOOLHOLDER CONE
Page 33 and 34: HSD 1 2 3 4 5 6 UTENSILE BLOCCATO U
Page 35 and 36: HSD 11.1 DAILY MAINTENANCE 11.1.1 C
Page 37 and 38: HSD § 12 REPLACEMENT OF COMPONENTS
Page 39 and 40: HSD 12.1.2 Replacement and adjustme
Page 41 and 42: HSD 12.1.5 Sensor S5 adjustment Aft
Page 43 and 44: HSD § 14 LIST OF SPARE PARTS CODE
Page 45 and 46: HSD The tool holder is not locked:
Page 47 and 48: HSD § 16 DECLARATION OF INCORPORAT

ES721 ISO40 7 kW NL - HSD

Create successful ePaper yourself

Delete template?

Save as template?