ES721 ISO40 7 kW NL - HSD

More documents

Recommendations

Info

HSD § 15 TROUBLESHOOTING PROBLEMS CAUSES REMEDIES The electrospindle does not turn: There is no power No tool holder is fitted Fit a tool holder. The tool holder not correctly seated The thermal switch has tripped The inverter switch has tripped Sensor S1 or sensor S5 are disconnected or faulty � Check the mains power supply. � Check all power terminals. � Check all electrical cables and connections for breaks. See “The tool holder is not locked” below. Wait for the electrospindle to cool down and the thermal switch will automatically reset. If the thermal switch trips frequently, see “The electrospindle overheats” below. Consult the inverter's own manual or contact the inverter manufacturer. � Check the sensor connectors. � Check the sensor cables for breaks. � Contact the HSD technical assistance service. 5801H0066 en Rev.01 44/48
HSD The tool holder is not locked: The tool holder is not ejected: There is no air pressure inside the electrospindle: One of the sensors does not give the required output: There is dirt or foreign bodies between the tool holder and the spindle shaft housing The tool holder cone is not of the right type There is insufficient air pressure to open the collet Sensor S2 is disconnected or faulty There is insufficient air pressure There is insufficient air pressure or the compressed air system is faulty A sensor is disconnected or faulty Remove any large foreign bodies and clean the tool holder cone and spindle housing as instructed in section § 11. Choose a tool holder as instructed in section § 10. � Check the air pressure settings in accordance with section 8.1 ; � Check the compressed air system for leaks and pressure losses. � Check the sensor connectors. � Check the sensor cables for breaks. � Contact the HSD technical assistance service. � Check the air pressure settings in accordance with paragraph 8.1 ; � Check the compressed air system for leaks and pressure losses. � Check the air pressure settings in accordance with sections 8.1 ; � Check the compressed air system for leaks and pressure losses; � Contact the HSD Technical Assistance Service. � Check the sensor connectors; � Check the sensor cables for breaks; � Contact the HSD technical assistance service. 5801H0066 en Rev.01 45/48
Page 1 and 2: HSD MECHATRONIC D I V I S I O N HSD
Page 3 and 4: HSD 10.7.2 Electrospindle states an
Page 5 and 6: HSD § 4 TERMS OF WARRANTY HSD S.p.
Page 7 and 8: HSD 5.3 RISKS ASSOCIATED WITH THE E
Page 9 and 10: HSD § 6 TRANSPORT, PACKAGING, UNPA
Page 11 and 12: HSD § 7 TECHNICAL SPECIFICATIONS 7
Page 13 and 14: HSD § 8 DIMENSIONS AND MAIN PARTS
Page 15 and 16: HSD 8.1.2 Direct liquid coolant cou
Page 17 and 18: HSD 8.1.3 Deublin distributor, enco
Page 19 and 20: HSD § 9 INSTALLAZIONE HSD S.p.a. d
Page 21 and 22: HSD DPC 5801H0066 en Rev.01 21/48 !
Page 23 and 24: HSD 9.7 COMPRESSED AIR SPECIFICATIO
Page 25 and 26: HSD 9.10 AUTOMATIC CONE CLEANING 1.
Page 27 and 28: HSD § 10 OPERATION 10.1 GENERAL PR
Page 29 and 30: HSD 10.7.2 Electrospindle states an
Page 31 and 32: HSD 10.10 CHOICE OF TOOLHOLDER CONE
Page 33 and 34: HSD 1 2 3 4 5 6 UTENSILE BLOCCATO U
Page 35 and 36: HSD 11.1 DAILY MAINTENANCE 11.1.1 C
Page 37 and 38: HSD § 12 REPLACEMENT OF COMPONENTS
Page 39 and 40: HSD 12.1.2 Replacement and adjustme
Page 41 and 42: HSD 12.1.5 Sensor S5 adjustment Aft
Page 43: HSD § 14 LIST OF SPARE PARTS CODE
Page 47 and 48: HSD § 16 DECLARATION OF INCORPORAT

ES721 ISO40 7 kW NL - HSD

Create successful ePaper yourself

Delete template?

Save as template?