ES721 ISO40 7 kW NL - HSD

More documents

Recommendations

Info

HSD The electrospindle overheats: Performance below specifications: The electrospindle vibrates: The bearings are noisy: Cooling problems: The machining is taking up too much power The inverter setup is incorrect The inverter setup is incorrect The tool holder is not balanced The tool is not balanced There is dirt or foreign bodies between the tool holder and the spindle shaft housing The inverter setup is incorrect The machining is taking up too much power � Check cooling circuit specifications in section 9.4 ; � Check the cooling system for leaks and losses or clogging. � Contact the HSD Technical Assistance Service. Reduce the machining power requirements. Check the specifications of the electrospindle on its data label and in paragraph 7.1 . Check the specifications of the electrospindle on its data label and in paragraph 7.1 . Choose a tool holder in accordance with paragraph § 10. Choose a tool in accordance with paragraph § 10. Remove any large foreign bodies and clean the tool holder cone and spindle housing as instructed in section § 11. Check the specifications of the electrospindle on its data label and in paragraph 7.1 . Reduce the machining power requirements. The fixing bolts are loose Tighten the fixing bolts. The bearings are worn or Contact the HSD technical damaged assistance service. The bearings are worn or Contact the HSD technical damaged assistance service. 5801H0066 en Rev.01 46/48
HSD § 16 DECLARATION OF INCORPORATION Pesaro 29/07/2010 ELECTROSPINDLE MODEL 794 5801H0066 en Rev.01 47/48
Page 1 and 2: HSD MECHATRONIC D I V I S I O N HSD
Page 3 and 4: HSD 10.7.2 Electrospindle states an
Page 5 and 6: HSD § 4 TERMS OF WARRANTY HSD S.p.
Page 7 and 8: HSD 5.3 RISKS ASSOCIATED WITH THE E
Page 9 and 10: HSD § 6 TRANSPORT, PACKAGING, UNPA
Page 11 and 12: HSD § 7 TECHNICAL SPECIFICATIONS 7
Page 13 and 14: HSD § 8 DIMENSIONS AND MAIN PARTS
Page 15 and 16: HSD 8.1.2 Direct liquid coolant cou
Page 17 and 18: HSD 8.1.3 Deublin distributor, enco
Page 19 and 20: HSD § 9 INSTALLAZIONE HSD S.p.a. d
Page 21 and 22: HSD DPC 5801H0066 en Rev.01 21/48 !
Page 23 and 24: HSD 9.7 COMPRESSED AIR SPECIFICATIO
Page 25 and 26: HSD 9.10 AUTOMATIC CONE CLEANING 1.
Page 27 and 28: HSD § 10 OPERATION 10.1 GENERAL PR
Page 29 and 30: HSD 10.7.2 Electrospindle states an
Page 31 and 32: HSD 10.10 CHOICE OF TOOLHOLDER CONE
Page 33 and 34: HSD 1 2 3 4 5 6 UTENSILE BLOCCATO U
Page 35 and 36: HSD 11.1 DAILY MAINTENANCE 11.1.1 C
Page 37 and 38: HSD § 12 REPLACEMENT OF COMPONENTS
Page 39 and 40: HSD 12.1.2 Replacement and adjustme
Page 41 and 42: HSD 12.1.5 Sensor S5 adjustment Aft
Page 43 and 44: HSD § 14 LIST OF SPARE PARTS CODE
Page 45: HSD The tool holder is not locked:

ES721 ISO40 7 kW NL - HSD

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?