Ursalink UR51 Industrial Cellular Router User Guide

More documents

Recommendations

Info

UR51 User Guide Port Setting Item Port Status Property Speed Duplex Description Users can define the Ethernet ports according to their needs. Set the status of Ethernet port; select "up" to enable and "down" to disable. LAN. User cannot change this setting. Set the Ethernet port's speed. The options are "auto", "1000 Mbps", "100 Mbps", and "10 Mbps". Set the Ethernet port's mode. The options are "auto", "full", and "half". Table 4-2-1-1 Port Parameters 4.2.1.2 LAN LAN setting is used for managing local area network devices which are connected to LAN port of the UR51, allowing each of them to access the Internet. Click to delete the existing LAN port setting. Click to add a new LAN port setting. LAN Figure 4-2-1-2 Item Description Default Interface Select LAN port. FE 0 IP Address Set IP address of LAN port. 192.168.1.1 Netmask Set Netmask of LAN port. 255.255.255.0 MTU Set the maximum transmission unit of LAN port. Range: 68-1500. Table 4-2-1-2 1500 Related Configuration Example LAN Management 4.2.1.3 VLAN Trunk VLAN is a kind of new data exchange technology that realizes virtual work groups by logically dividing the LAN device into network segments. Client to delete the current VLAN setting. Click to add a new VLAN port. 28
UR51 User Guide VLAN Trunk Item Enable Interface Description Figure 4-2-1-3 The router can encapsulate or decapsulate the virtual LAN tag when this function is enabled. Select the VLAN interface from the LAN ports. VID Set the label ID of the VLAN. Range: 1-4094. IP Address Netmask Set VLAN port's IP address. Set VLAN port's netmask. Table 4-2-1-3 VLAN Trunk Parameters 4.2.1.4 Cellular This section explains how to set the related parameters for cellular network. The UR51 cellular router has two cellular interfaces, namely SIM1 and SIM2. Only one cellular interface is active at one time. If both cellular interfaces are enabled, then SIM1 interface takes precedence by default. A typical use case would be to have SIM1 configured as the primary cellular interface and SIM2 as a backup. If the UR51 cannot connect to the network via SIM1, it will automatically fail over to SIM2. Figure 4-2-1-4 29
Page 1 and 2: UR51 User Guide 1
Page 3 and 4: UR51 User Guide Declaration of Conf
Page 5 and 6: UR51 User Guide 4.2.2.4 MAC Binding
Page 7 and 8: UR51 User Guide Chapter 1 Product I
Page 9 and 10: UR51 User Guide Security & Reliabil
Page 11 and 12: UR51 User Guide Power Consumption P
Page 13 and 14: UR51 User Guide 2.2 Product Overvie
Page 15 and 16: UR51 User Guide PIN Description 11
Page 17 and 18: UR51 User Guide 2.10.2 DIN Rail Mou
Page 19 and 20: UR51 User Guide Chapter 3 Access to
Page 21 and 22: UR51 User Guide If the SIM card is
Page 23 and 24: UR51 User Guide 4.1.2 Cellular You
Page 25 and 26: UR51 User Guide 4.1.4 VPN You can c
Page 27: UR51 User Guide Interface Metric AR
Page 31 and 32: UR51 User Guide Server PING Times P
Page 33 and 34: UR51 User Guide 4.2.2 Firewall This
Page 35 and 36: UR51 User Guide DMZ Item Enable DMZ
Page 37 and 38: UR51 User Guide QoS Item Download/U
Page 39 and 40: UR51 User Guide 4.2.4.2 DHCP Relay
Page 41 and 42: UR51 User Guide 3. Define applicati
Page 43 and 44: UR51 User Guide to the time set her
Page 45 and 46: UR51 User Guide 4.2.7 Routing 4.2.7
Page 47 and 48: UR51 User Guide from the routing ta
Page 49 and 50: UR51 User Guide 4.2.7.3 OSPF OSPF,
Page 51 and 52: UR51 User Guide (s) Interface Advan
Page 53 and 54: UR51 User Guide Dead Interval Retra
Page 55 and 56: UR51 User Guide The UR51 supports D
Page 57 and 58: UR51 User Guide Figure 4-2-8-2 IPse
Page 59 and 60: UR51 User Guide PFS Group Select fr
Page 61 and 62: UR51 User Guide L2TP Item Enable Re
Page 63 and 64: UR51 User Guide Global Traffic Forw
Page 65 and 66: UR51 User Guide OpenVPN Client Item
Page 67 and 68: UR51 User Guide Remote Virtual IP C
Page 69 and 70: UR51 User Guide OpenVPN Server Item
Page 71 and 72: UR51 User Guide Figure 4-3-1-4 Figu
Page 73 and 74: UR51 User Guide 4.3.1.5 Phone Phone
Page 75 and 76: UR51 User Guide Account Item Userna
Page 77 and 78: UR51 User Guide 4.3.3.2 MIB View Th
Page 79 and 80:
UR51 User Guide 4.3.3.5 MIB This se
Page 81 and 82:
UR51 User Guide LDAP Item Enable Se
Page 83 and 84:
UR51 User Guide Disconnected Activa
Page 85 and 86:
UR51 User Guide Related Topics Emai
Page 87 and 88:
UR51 User Guide DTU Mode Figure 4-4
Page 89 and 90:
UR51 User Guide 4.4.2 Modbus Master
Page 91 and 92:
UR51 User Guide Alarm Setting Item
Page 93 and 94:
UR51 User Guide Schedule Item Sched
Page 95 and 96:
UR51 User Guide upgrade will be int
Page 97 and 98:
UR51 User Guide Figure 4-5-6-1 97
Page 99 and 100:
UR51 User Guide Configuration proce
Page 101 and 102:
UR51 User Guide Then the current co
Page 103 and 104:
UR51 User Guide Please wait till th
Page 105 and 106:
UR51 User Guide 105
Page 107 and 108:
UR51 User Guide Configure the corre
Page 109 and 110:
UR51 User Guide 2. Click “ ” to
Page 111 and 112:
UR51 User Guide 2. Start “ManageE
Page 113 and 114:
UR51 User Guide box. You can get ot
Page 115 and 116:
UR51 User Guide If you select “Au
Page 117 and 118:
UR51 User Guide Then click “Save
Page 119 and 120:
UR51 User Guide Configuration Steps
Page 121 and 122:
UR51 User Guide changes take effect
Page 123 and 124:
UR51 User Guide of cellular interfa
Page 125 and 126:
UR51 User Guide 3. Configure TCP se
Page 127 and 128:
UR51 User Guide 8. After serial com
Page 129:
UR51 User Guide If the PPTP server
show all

Ursalink UR51 Industrial Cellular Router User Guide

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?