CNC 8037 T - Manual de programación - Fagor Automation
CNC 8037 T - Manual de programación - Fagor Automation
CNC 8037 T - Manual de programación - Fagor Automation
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>Manual</strong> <strong>de</strong> <strong>programación</strong><br />
Formato <strong>de</strong> <strong>programación</strong>:<br />
Plano XY: G02(G03) X±5.5 Y±5.5 I±6.5 J±6.5<br />
Plano ZX: G02(G03) X±5.5 Z±5.5 I±6.5 K±6.5<br />
Plano YZ: G02(G03) Y±5.5 Z±5.5 J±6.5 K±6.5<br />
In<strong>de</strong>pendientemente <strong>de</strong>l plano seleccionado, se mantendrá siempre el or<strong>de</strong>n <strong>de</strong> <strong>programación</strong> <strong>de</strong><br />
los ejes, así como el <strong>de</strong> las respectivas cotas <strong>de</strong>l centro.<br />
Plano AY: G02(G03) Y±5.5 A±5.5 J±6.5 I±6.5<br />
Plano XU: G02(G03) X±5.5 U±5.5 I±6.5 I±6.5<br />
Coor<strong>de</strong>nadas polares<br />
Será necesario <strong>de</strong>finir el ángulo a recorrer Q y la distancia <strong>de</strong>s<strong>de</strong> el punto <strong>de</strong> partida al centro<br />
(opcional), según los ejes <strong>de</strong>l plano <strong>de</strong> trabajo.<br />
Las cotas <strong>de</strong>l centro, se <strong>de</strong>finirán en radios y mediante las letras I, J o K, estando cada una <strong>de</strong> ellas<br />
asociada a los ejes <strong>de</strong>l siguiente modo:<br />
Ejes X, U, A ==> I<br />
Ejes Y, V, B ==> J<br />
Ejes Z, W, C ==> K<br />
Si no se <strong>de</strong>fine el centro <strong>de</strong>l arco, el <strong>CNC</strong> interpretará que este coinci<strong>de</strong> con el origen polar vigente.<br />
Formato <strong>de</strong> <strong>programación</strong>:<br />
Plano XY: G02(G03) Q±5.5 I±6.5 J±6.5<br />
Plano ZX: G02(G03) Q±5.5 I±6.5 K±6.5<br />
Plano YZ: G02(G03) Q±5.5 J±6.5 K±6.5<br />
Coor<strong>de</strong>nadas cartesianas con <strong>programación</strong> <strong>de</strong> radio<br />
Se <strong>de</strong>finirán las coor<strong>de</strong>nadas <strong>de</strong>l punto final <strong>de</strong>l arco y el radio R.<br />
Formato <strong>de</strong> <strong>programación</strong>:<br />
Plano XY: G02(G03) X±5.5 Y±5.5 R±6.5<br />
Plano ZX: G02(G03) X±5.5 Z±5.5 R±6.5<br />
Plano YZ: G02(G03) Y±5.5 Z±5.5 R±6.5<br />
Si se programa una circunferencia completa, con la <strong>programación</strong> <strong>de</strong> radio, el <strong>CNC</strong> visualizará el<br />
error correspondiente, <strong>de</strong>bido a que existen infinitas soluciones.<br />
6.<br />
CONTROL DE LA TRAYECTORIA<br />
Interpolación circular (G02, G03)<br />
<strong>CNC</strong> <strong>8037</strong><br />
MODELO ·T·<br />
SOFT: V01.4X<br />
·79·