Register and win! WRP 10000 WRP 20000 - Kärcher

More documents

Recommendations

Info

1 ON/OFF switch 2 Fresh water supply key was active / indicator lamp fresh water supply 3 Reflushing key / indicator lamp reflushing running 4 Pump basin key / automatic guide value monitoring Symbol Colour of indicator lamp Meaning Green Plant is working OFF AUTO MAN Operation Operating elements 5 Indicator lamp - Operation 6 Indicator lamp - fault 7 Indicator lamp emptying pump basin 8 Water connections 9 Multi-channel valve 10 Setting the backwash and initial filtrate duration Yellow Start backwash Backwash running Red Fault Yellow Fresh water supply is active Fresh water supply key was active / acknowledge message Yellow Draining the pump basin (MAN) Automatic conductivity monitoring (AUTO) Yellow The pump basin in emptied --- Switches on/off the system. 14 EN - 2 11 time switch 12 PRÜFTASTE/TESTBUTTON switch 13 ON key 14 OFF key 15 DRAIN key 16 Gravel filter 17 Remaining discharge - gravel filter
Switch-off in case of emergency Switch off the system. Pull the mains plug. Switching on the plant Switch on the ON/OFF switch. Immersion pump is working when: – a backwash is performed. – The water level in the recycled water tank is below the starting level S7. – the water level in the pump basin is above the starting level S4.1. Backwash During backwash, the dirt collected in the gravel filter is removed. To do this, the gravel filter is rinsed in the reverse direction. The rinsed dirt is routed to the sludge collector of the recycling system. The plant is equipped with an automatic time-controlled multi-channel valve. The backwash process is automatically started by the backwash clock. During the backwashing process, indicator lamp "Backwash gravel filter" glows. Note During normal operations, the backwash is performed once a day. During backwash, the recycled water tank is not refilled with recycled water. If the washing system is not operated during backwash, then refilling is done automatically by the emergency fresh water supply (option). The WRP is equipped with an on-demand backflushing function. This backflush is initiated automatically if filling the recycled water tank takes more than 15 minutes (30 minutes for 2 tanks, 45 minutes for 3 tanks) due to a heavily soiled filter. This automatic filter backflushing can also be started during a wash in a very busy washing operation with consequential filter contamination. The water demand of the washing system is ensured via the fresh water supply (option). After backflushing, another automatic backflush is blocked for 90 minutes. With increased water use of the washing system, this will avoid superfluous backflushing. The filter performance does not decrease too much during this time, so that a sufficient supply of recycled water is ensured. Operating the multi-channel valve manually You can use the button located on the side of the control head to manually operate the automatic backwash valve. The buttons trigger the following functions: Button Function EIN/ON The multi-channel valve is switched on and goes to Filter position. (Is done automatically when you switch on the system using the ON/OFF switch.) AUS/OFF The multiple-channel valve is switched off. The current valve position is retained. ENTLEER- Adjustment not required. EN/ DRAIN PRÜFTASTE/ TESTBUT- TON A backwash process is started. Setting the rinsing times The backwash and the clear rinse time are set at two rotary potentiometers in the control head according to the scaling. 1 Backwash time 2 Clear rinse time Unscrew the 6 screws on the cover of the control head of the multi-channel valve and remove the cover. Set backwash time to 5 minutes. Set backwash time to 1 minutes. Replace the lid of the control head and tighten all screws. Start the backwash cycle by pressing the "TEST BUTTON" button and measure the rinse time; correct it, if required. Emptying the pump basin – Turn the rotary button "Empty pump basin" to "MAN" position to route the recycled water via the WRP 10000/20000 and the recycled water tank from the pump basin into the canal. – This function is required when the quality of the recycled water proves insufficient for operating the awashing system (too much salt in the water or wrong cleaning agent, for example). Function: Actuate the button once (rotate to MAN and release it). – The WRP 10000/20000 filters until the S4.2 switch in the pump basin signals lack of water and the submersion pump is switched off. – This overfills the recycled water tank. The excess water flows though the overflow pipe of the recycled water tank into the canal. – The water supply of the washing system now runs with fresh water until the EN - 3 pump basin is filled up to level S4.1 at the top, and the deactivation of the submerged pump is cancelled. – Recycled water can then be produced in the normal way. – KÄRCHER Service deactivates the "Draining the pump basin" function if there is no overflow line th the channel. Conductivity monitoring – Monitoring the recycled water conductivity automatically is an option of the WRP 10000/20000. – The measuring point is in the recycled water tank. – Conductivity monitoring can be activated (AUTO) or deactivated (OFF) at the rotary switch "Automatic conductivity monitoring". – When a value of 3000 μS/cm is exceeded, conductivity monitoring triggers the same process as the "Empty pump basin" button. – The subsequent utilization of fresh water for the washing process dilutes the remaining salty water in the basin system to an extent that adequate washing water quality is restored. – This option cannot be installed if the recycling system is not equipped with an overflow from the recycled water tank and a fresh water supply. Recycling water recirculation If the washing system does not use up the water, the recycled water is circulated by means of gravity to avoid foul odour. If a gravity circulation is not possible (e.g. if the technical room is below the system), the circulation pump upgrade kit is required. Frost protection The plant must be operated in frost-free rooms. During frost, put the system out of operation and remove all traces of water: Loosen the screws of the plastic pipes and let the pipes run empty. Empty the recycled water tank. Open the gravel filer and remove the gravel that is still moist (Customer Service) Shutdown Note To avoid odour problems, the plant must remain switched on even during the night. Switch off the ON/OFF switch. If there is risk of frosting, then any existing water traces must be removed (see section "Anti-freezing"). Restarting During fresh start-up after shutdown: Switch on plant. Backwash the filter until the manometer on the multi-channel valve displays an inlet pressure of 0.05 MPa (0.5 bar) during filter operation. 15
Page 1: WRP 10000 WRP 20000 Register and wi
Page 4 and 5: 1 Ein-/Aus Schalter 2 Taster Frisch
Page 6 and 7: 1 Schlammfang des Recyclingsystems
Page 8 and 9: Überwachungs- und Regeleinrichtung
Page 10 and 11: Die Durchflussleistung des Filters
Page 12 and 13: Filterkies, fein Bestell-Nr.: 6.272
Page 16 and 17: 1 Sludge collection of the recyclin
Page 18 and 19: Monitoring and regulating equipment
Page 20 and 21: The flow performance of the filter
Page 22 and 23: Accessories Filter gravel, fine Ord
Page 24 and 25: 1 Interrupteur - Marche/Arrêt 2 Bo
Page 26 and 27: Circulation de l'eau de recyclage S
Page 28 and 29: 1 Collecteur de boue du système de
Page 30 and 31: Période Action Sous-groupe concern
Page 32 and 33: Panne Eventuelle cause Remède Par
Page 34 and 35: Prima di utilizzare l'apparecchio p
Page 36 and 37: Spegnimento in caso di emergenza Di
Page 38 and 39: 1 Separatore di fanghi del sistema
Page 40 and 41: Dispositivi di controllo e regolazi
Page 42 and 43: La portata del filtro può essere r
Page 44 and 45: Accessori Ghiaia da filtro, fine Co
Page 46 and 47: 1 Schakelaar -Aan/Uit 2 Taster vers
Page 48 and 49: Stillegging Waarschuwing Om geurpro
Page 50 and 51: 1 Slibopvang van het recyclingsyste
Page 52 and 53: Tijdstip Handeling Betrokken compon
Page 54 and 55: Storing Mogelijke oorzaak Oplossing
Page 56 and 57: Antes del primer uso de su aparato,
Page 58 and 59: Desconectar en caso de emergencia D
Page 60 and 61: 1 Atrapar el barro del sistema de r
Page 62 and 63: Dispositivos de supervisión y regu
Page 64 and 65:
El volumen de flujo del filtro se p
Page 66 and 67:
Accesorios Gravilla filtrante, fina
Page 68 and 69:
1 Interruptor Lig/Desl 2 A tecla "A
Page 70 and 71:
Recirculação da água de reciclag
Page 72 and 73:
1 Captura de lama do sistema de rec
Page 74 and 75:
Momento da realização Actividade
Page 76 and 77:
Avaria Possível causa Eliminação
Page 78 and 79:
Læs original brugsanvisning inden
Page 80 and 81:
Slukke i nødstilfælde Afbryd anl
Page 82 and 83:
1 Genvindingssystemets slamkasse *)
Page 84 and 85:
Tidspunkt Aktivitet berørte kompon
Page 86 and 87:
Fejl Mulig årsag Afhjælpning Fra
Page 88 and 89:
Før første gangs bruk av apparate
Page 90 and 91:
Slå av i nødsfall Slå av anlegge
Page 92 and 93:
1 Slamfang til gjenvinningssystem*)
Page 94 and 95:
Tidspunkt Aktivitet Relevant kompon
Page 96 and 97:
Feil Mulige årsaker Retting Av hve
Page 98 and 99:
Läs bruksanvisning i original inna
Page 100 and 101:
Avstängning vid nödfall Stäng av
Page 102 and 103:
1 Återvinningssystemets slamuppsam
Page 104 and 105:
Tidpunkt Aktivitet Beträffad kompo
Page 106 and 107:
Störning Möjlig orsak Åtgärd Av
Page 108 and 109:
Lue tämä alkuperäisiä ohjeita e
Page 110 and 111:
Kytkentä pois päältä hätätila
Page 112 and 113:
1 Recycling-järjestelmän lietelou
Page 114 and 115:
Huoltokaavio Ajankohta Toiminta Rak
Page 116 and 117:
Häiriö Mahdollinen syy Apu Suorit
Page 118 and 119:
Πριν χρησιμοποιήσε
Page 120 and 121:
Απενεργοποίηση σε
Page 122 and 123:
1 Συλλέκτης λάσπης
Page 124 and 125:
Μηχανισμοί παρακολ
Page 126 and 127:
Η απόδοση ροής του
Page 128 and 129:
Εξαρτήματα Χαλίκι
Page 130 and 131:
1 Açma-Kapama şalteri 2 Temiz su
Page 132 and 133:
1 Geri dönüşüm sisteminin çamu
Page 134 and 135:
Denetim ve ayar düzenekleri Geri d
Page 136 and 137:
Filtrenin akış gücü aşağıdak
Page 138 and 139:
Aksesuar Filtre kumu, ince Sipariş
Page 140 and 141:
Опасность Опасност
Page 142 and 143:
Выключение в случа
Page 144 and 145:
1 шламоуловитель си
Page 146 and 147:
Котролирующие и ре
Page 148 and 149:
Пропускную способн
Page 150 and 151:
Принадлежности Гра
Page 152 and 153:
1 Be/Ki kapcsoló 2 A friss víz ho
Page 154 and 155:
1 a recycling rendszer sárfogója*
Page 156 and 157:
Felügyeleti- és biztonsági beren
Page 158 and 159:
A szűrő átfolyási teljesítmén
Page 160 and 161:
Szűrőkavics, finom Megrendelési
Page 162 and 163:
1 Vypínač 2 Tlačítko přidává
Page 164 and 165:
1 Kalová jímka recyklačního sys
Page 166 and 167:
Monitorovací a regulační zaříz
Page 168 and 169:
Průtokový výkon filtru lze zjist
Page 170 and 171:
Příslušenství Filtrační ště
Page 172 and 173:
1 Stikalo za vklop/izklop 2 Tipka z
Page 174 and 175:
1 Lovilnik blata reciklirnega siste
Page 176 and 177:
Nadzorovalne in regulacijske pripra
Page 178 and 179:
Pretočna zmogljivost filtra se lah
Page 180 and 181:
Pribor Filtrirni pesek, droben Naro
Page 182 and 183:
1 Wyłącznik 2 Przycisk Dolewanie
Page 184 and 185:
Przetłaczanie wody z recyklingu Je
Page 186 and 187:
1 Łapacz osadu systemu recyklingu
Page 188 and 189:
Termin Zajęcie Dane podzespoły co
Page 190 and 191:
Usterka Możliwa przyczyna Usuwanie
Page 192 and 193:
Înainte de prima utilizare a apara
Page 194 and 195:
Oprirea în caz de urgenţă Opriţ
Page 196 and 197:
1 Separatorul de noroi în cadrul s
Page 198 and 199:
Sisteme de monitorizare şi de regl
Page 200 and 201:
Debitul a filtrului poate fi determ
Page 202 and 203:
Accesorii Pietriş de filtrare, fin
Page 204 and 205:
1 Vypínač 2 Tlačidlo Pridanie č
Page 206 and 207:
1 Zachytávanie kalu recyklačného
Page 208 and 209:
kontrolné a regulačné zariadenia
Page 210 and 211:
Prietokový výkon filtra sa môže
Page 212 and 213:
Príslušenstvo Štrk filtra, jemn
Page 214 and 215:
1 Glavni prekidač 2 Tipka za dodav
Page 216 and 217:
1 Sakupljanje mulja sustava za reci
Page 218 and 219:
Nadzorni i regulacijski elementi Pr
Page 220 and 221:
Snaga protoka filtra može se utvrd
Page 222 and 223:
Pribor Šljunak za filtar, fini Kat
Page 224 and 225:
1 Prekidač za uključivanje/isklju
Page 226 and 227:
Cirkulacija reciklirane vode Ako pe
Page 228 and 229:
1 Hvatanje blata sistema reciklaže
Page 230 and 231:
Vreme izvođenja Delatnost Sklop ko
Page 232 and 233:
Smetnja Moguć uzrok Otklanjanje Iz
Page 234 and 235:
Преди първото изпо
Page 236 and 237:
Изключване при ава
Page 238 and 239:
1 Шламоуловител на
Page 240 and 241:
Контролни и регули
Page 242 and 243:
Мощността на поток
Page 244 and 245:
Принадлежности Фил
Page 246 and 247:
1 Sisse/välja lüliti 2 Puhta vee
Page 248 and 249:
1 Ringlussüsteemi mudapüüdur *)
Page 250 and 251:
Kontroll- ja reguleerimisseadissed
Page 252 and 253:
Filtri läbivooluvõimsust saab kin
Page 254 and 255:
Tarvikud Filtrikruus, peen Tellimis
Page 256 and 257:
1 Įjungiklis/išjungiklis 2 Mygtuk
Page 258 and 259:
Išjungimas Pastaba Kad būtų išv
Page 260 and 261:
1 Perdirbimo sistemos šlamo gaudyk
Page 262 and 263:
Terminas Užduotis Prietaiso dalių
Page 264 and 265:
Gedimas Galimos priežastys Šalini
Page 266 and 267:
Pirms ierīces pirmās lietošanas
Page 268 and 269:
Izslēgšana avārijas gadījumā I
Page 270 and 271:
1 Otrreizējās pārstrādes sistē
Page 272 and 273:
Kad Veicamais darbs Detaļa, kurai
Page 274 and 275:
Darbības traucējums Iespējamais
Page 276 and 277:
Перед першим засто
Page 278 and 279:
1 Вимикач 2 Клавіша
Page 280 and 281:
Перевірка провідно
Page 282 and 283:
1 шламоуловлювач си
Page 284 and 285:
Дата Вид відповідн
Page 286 and 287:
Несправність Можли
Page 288:
AE Karcher FZE, P.O. Box 17416, Jeb
show all

Register and win! WRP 10000 WRP 20000 - Kärcher

Create successful ePaper yourself

Delete template?

Save as template?