Register and win! WRP 10000 WRP 20000 - Kärcher
Register and win! WRP 10000 WRP 20000 - Kärcher
Register and win! WRP 10000 WRP 20000 - Kärcher
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Fault Possible cause Remedy By whom<br />
Indicator Lamp<br />
"Fault" illuminates<br />
Message "Recycled<br />
water tank empty"<br />
displayed on washing<br />
system.<br />
The swimmer switch S4.2 has triggererd<br />
<strong>and</strong> S4.1 is not in the top position.<br />
Washing system runs with fresh water until level<br />
S4.1 top is reached. Find the cause.<br />
- 9<br />
Customer Service<br />
Float switch S4 in pump basin is defective. Repair or replace float switch. Customer Service<br />
Motor protection switch of the immersion<br />
pump has been triggered.<br />
Water level in the pump basin is too low <strong>and</strong><br />
emergency fresh water supply has failed<br />
Reset motor protection switch; call Customer Service<br />
if the problem recurs.<br />
Refill pump basin; check emergency fresh water<br />
supply; repair, if required.<br />
Operator<br />
Operator, Customer<br />
Service<br />
Float switch S11 is defective or loose Replace the float switch or reattach it Customer Service<br />
Immersion pump has failed, is dirty or defective<br />
Restart the plant by switching off <strong>and</strong> on; otherwise<br />
call Customer service<br />
Operator<br />
Pipe connections are leaky Check all pipe connections; seal them, if required Operator, Customer<br />
Service<br />
Controls are defective Check, repair or replace controls Customer Service<br />
Gravel filter plugged (filter output is too low) Backwash several times; if not successful, change<br />
the gravel<br />
Operator/Customer<br />
Service<br />
Multi-channel defective Repair multi-channel valve; replace defective parts Customer Service<br />
Plant out of order Power supply is interrupted Check power supply <strong>and</strong> ensure proper supply. Operator<br />
Controls are defective Check, repair or replace controls Customer Service<br />
Processed water is<br />
coloured or is foaming<br />
too much<br />
Water in the processed<br />
water tank has<br />
a bad odour<br />
Continuous flow<br />
sound<br />
Immersion pump is<br />
not functioning<br />
Filter output is too<br />
low<br />
Fresh water consumption<br />
is too high<br />
Sludge collector or pump basin is dirty Emptying <strong>and</strong> cleaning the basins Operator/ Disposal<br />
agency<br />
Improper detergents are used in the washing<br />
unit or washing hall<br />
Detergent dosing in the washing unit is too<br />
high<br />
Washing place cleaned with incompatible<br />
detergents<br />
<strong>WRP</strong> was switched off during the night or<br />
over the weekend<br />
none or very poor circulation, very little ventilation<br />
Float switch, control or fresh water solenoid<br />
valve defective<br />
Use compatible detergents; rinse the system, if<br />
necessary<br />
Operator, Customer<br />
Service<br />
Check detergent dosing; reset, if necessary Operator, Customer<br />
Service<br />
Replace water <strong>and</strong> rinse the basins Operator<br />
<strong>WRP</strong> must be ON continuously Operator<br />
Check whether the recirculation valve is open <strong>and</strong><br />
if the flow is at least 1.5 m 3 / (<strong>WRP</strong> 10,000) or 2.0<br />
m 3 /h (<strong>WRP</strong> 20,000).<br />
Check pipes for dirt <strong>and</strong> damage; clean or replace<br />
them as required<br />
Check the ventilation, the ventilator must clearly<br />
bubble in the pump basin.<br />
Operator<br />
Operator, Customer<br />
Service<br />
Customer Service<br />
Check, repair or replace the concerned component Operator, Customer<br />
Service<br />
Water level in the pump basis is too low Washing system runs with fresh water until level<br />
S4.1 top is reached. Find the cause.<br />
Float switch S7 defective Check the float switch; clean, repair or replace it as<br />
required<br />
Control head of multi-channel valve is defective<br />
Customer Service<br />
Operator, Customer<br />
Service<br />
Repair control head Customer Service<br />
Controls are defective Check, repair or replace controls Customer Service<br />
Gravel filter is blocked Backwash gravel filter or change the gravel. If the<br />
problem recurs, increase the backwash duration<br />
<strong>and</strong>/or increase the frequency.<br />
Operator, Customer<br />
Service<br />
Immersion pump is blocked, defective Clean, repair, replace immersion pump Operator, Customer<br />
Service<br />
Pipe or valve is leaky, defective, blocked Check pipes <strong>and</strong> valves; clean, repair or replace as<br />
required<br />
Operator, Customer<br />
Service<br />
Float switch S9 is defective. Replace Customer Service<br />
Conductivity sensor is defective or contaminated.<br />
EN<br />
Check; clean, replace, if required. Operator, Customer<br />
Service<br />
21