BRESIMAR(asaTek)-Beckhoff-Livro Formação Técnica TwinCAT 2

More documents

Recommendations

Info

TWINCAT PLC – Lista de erros BECKHOFF New Automation Technology 3208 Conversion not implemented yet 3209 Operator not implemented 3210 Function '' not found 3211 Max string usage exceeded 3250 Real not supported for 8 Bit Controller 3251 date of day types are not supported for 8 Bit Controller 3252 size of stack exceeds bytes 3253 Could not find hex file: '' 3254 Call to external library function could not be resolved. 3400 An error occurred during import of Access variables 3401 An error occurred during import of variable configuration 3402 An error occurred during import of global variables 3403 Could not import 3404 An error occurred during import of task configuration 3405 An error occurred during import of PLC configuration 3406 Two steps with the name '
TWINCAT PLC – Lista de erros BECKHOFF New Automation Technology points to an used memory! 3455 Error during load: GSD- File '' could not be found, but is referenced in hardware configuration! 3456 The profibus device '' couldn't be created! 3457 Error in module description! 3500 No 'VAR_CONFIG' for '' 3501 No address in 'VAR_CONFIG' for ''. 3502 Wrong data type for '' in 'VAR_CONFIG 3503 Wrong data type for '' in 'VAR_CONFIG' 3504 Initial values are not supported for 'VAR_CONFIG 3505 '’is no valid dialog ‚Settings’ of the PLC configuration and an overlap has been detected. Regard, that the area check is based on the size which results of the data types of the modules, the size which is given by the entry ‚size’ in the configuration file. Eventually the device file required by the Profibus configuration is not in the correct directory. . Check the directory setting for configuration files in ‚Project' 'Options' 'Directories'. The device file for module does not fit to the current configuration. Eventually it has been modified since the configuration has been set up or it is corrupted. Please check the device file of this module. Insert a declaration for this variable in the global variable list which contains the 'Variable_Configuration'. Assign an address to this variable in the global variable list which contains the 'Variable_Configuration'. In the global variables list which contains the‚ ‘Variable_Configuration’ the variable is declared with a different data type than in the POU. In the global variables list which contains the‚ ’Variable_Configuration’ the variable is declared with a different address than in the POU. A variable of the ‚Variable_Configuration’ is declared with address and initial value. But an initial value can only be defined for input variables without address assignment. The Variable_Configuration contains a nonexisting variable. instance path 3506 Access path expected In the global variable list for Access Variables the access path for a variable is not correct. Correct: :'': 3507 No address specification for 'VAR_ACCESS'- variables 3550 Duplicate definition of identifier '' 3551 The task '' must contain at least one program call 3552 Event variable '' in task '%s' not defined 3553 "Event variable '' in task '%s' must be of type 'BOOL' 3554 Task entry '' must be a program or global function block instance 3555 The task entry '' contains invalid parameters The global variable list for Access Variables contains an address assignment for a variable. This is not allowed. Valid variable definition: :'': There are two tasks are defined with an identic same name. Rename one of them. Insert a program call or delete task. There is an event variable set in the ‘Single’ field of the task properties dialog which is not declared globally in the project. Use another variable or define the variable globally. Use a variable of type BOOL as event variable in the ‘Single’ field of the task properties dialog. In the field ‚Program call’ a function or a not defined POU is entered. Enter a valid program name. In the field ‚Append program call’ there are parameters used which do not comply with the declaration of the program POU. Use command ‚Rebuild all’. If nevertheless you get the error 3600 Implicit variables not found! message again please contact the PLC manufacturer. 3601 is a reserved The given variable is declared in the project, although it is variable name reserved for the codegenerator. Rename the variable. 3610 '' not supported The given feature is not supported by the current version of the programming system. 3611 The given compile There is an invalid directory given in the ‚Project’ ‚Options’ directory '' is ‚Directories’ for the Compile files. invalid 3612 Maximum number of POUs () exceeded! Compile is aborted. Too many POUs and data types are used in the project. Modify the maximum number of POUs in the Target Settings / Memory Layout. <strong>BRESIMAR</strong> Anexo B – 7 de 18
Page 1:
2009-01-12 mpro_twcplc.pdf (v1.2) B
Page 5 and 6:
TWINCAT PLC - Tipo de Dados e Varia
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
TWINCAT PLC - Lista de Instruções
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
TWINCAT PLC - Funções bloco “st
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
TWINCAT PLC - Funções “standard
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52: TWINCAT PLC - Exemplos práticos BE
Page 87 and 88: TWINCAT PLC - Resumo de Instruçõe
Page 97 and 98: TWINCAT PLC - Lista de erros BECKHO
Page 101: TWINCAT PLC - Lista de erros BECKHO
Page 113 and 114: TWINCAT PLC - Lista de erros 4501 E
show all

BRESIMAR(asaTek)-Beckhoff-Livro Formação Técnica TwinCAT 2

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?