BRESIMAR(asaTek)-Beckhoff-Livro Formação Técnica TwinCAT 2

More documents

Recommendations

Info

TWINCAT PLC – Lista de erros BECKHOFF New Automation Technology input '' of the box '' 4332 Expression expected at input '' of the box '' 4333 Identifier in jump expected 4334 Expression expected at the input of jump 4335 Expression expected at the input of the return 4336 Expression expected at the input of the output 4337 Identifier for input expected The input of the POU is of type VAR_IN_OUT and is not assigned. The given jump mark is not a valid identifier. Assign a boolean expression to the input of the jump. If this is TRUE, the jump will be executed. Assign a boolean expression to the input of the RETURN instruction. If this is TRUE, the jump will be executed. Assign a suitable expression to the output box. Insert a valid expression or identifier in the input box. 4338 Box '%s' has no inputs To none of the inputs of the operator POU '' a valid expression is assigned. 4339 Typemismatch at output: Cannot convert '' to ''. The type of the expression in the output box is not compatible to that of the expression which should be assigned to it. 4340 Jump requires 'BOOL' as input type 4341 Return requires 'BOOL' as input type 4342 Expression expected at input 'EN' of the box '' 4343 Values of Constants: ‘’ Make sure that the input for the jump is a boolean expression. Make sure that the input for the RETURN instruction is a boolean expression. Assign a valid boolean expression to the EN input of the box. Input '' of box '' is declared as VAR_INPUT CONSTANT. But to this POU box an expression has been assigned in the dialog 'Edit Parameters' which is not type compatible. Insert a valid boolean expression after the Set resp. Reset instruction. An expression is assigned to input '' of POU box '' which is not type compatible. 4344 'S' and 'R' require 'BOOL' operand 4345 Invalid Type for parameter '' of '': Cannot convert '' to ''. 4346 Not allowed to use a You can only assign an output to a variable or a direct constant as an output" address with write access. 4347 'VAR_IN_OUT' To VAR_IN_OUT parameters only variables with write parameter needs access can be handed over, because these can be modified variable with write within the POU. access as input. 4350 An SFC-Action can not SFC actions only can be called within the SFC POU in which be accessed from they are defined. outside! 4351 Step name is no Rename the step or choose a valid identifier as step name. identifier: '' 4352 Extra characters Remove the not valid characters in the step name. following valid step name:'' 4353 Step name duplicated: Rename one of the steps. '' 4354 Jump to undefined Choose an existent step name as aim of the jump resp. Step: '' insert a step with name ‚’. 4355 A transition must not A transition must be a boolean expression. have any side effects (Assignments, FB-Calls etc.) 4356 Jump without valid Step Use a valid identifier as aim (mark) of the jump. Name: '' 4357 IEC-Library not found Check whether the library iecsfc.lib is inserted in the library manager and whether the library paths defined in ‘Project’ ‘Options’ ‘Paths’are correct. 4358 Action not declared: '% s'. Make sure that in the object organizer the action of the IEC step is inserted below the SFC POU and that in the editor the action name is inserted in the box on the right hand of <strong>BRESIMAR</strong> Anexo B – 14 de 18
TWINCAT PLC – Lista de erros BECKHOFF New Automation Technology the qualifier. 4359 Invalid Qualifier: '%s' In the box on the left hand of the action name enter a qualifier for the IEC action. 4360 Time Constant expected after qualifier '%s' 4361 '%s' is not the name of an action Enter next to the box on the left hand of the action name a time constant behind the qualifier. Enter next to the box on the right hand of the qualifier the name of an action or the name of a variable which is defined in the project. Insert a boolean variable or a valid action name. 4362 Nonboolean expression used in action: '%s' 4363 IEC-Step name already Please rename the step or the variable. used for variable: '' 4364 A transition must be a The result of the transition expression must be of type boolean expression BOOL. 4365 Time Constant Open dialog ‚step attributes’ for the step '' and enter expected after qualifier a valid time variable or time constant '' 4366 The label of the parallel Enter a valid identifier next to the triangle which marks the branch is no valid jump label. identifier: '' 4367 The label '' is There is already a jump label or a step with this name. already used Please rename correspondingly. 4368 Action '' is used The action '' is used in the POU as well as in one or in multiple step chains, several actions of the POU. where one is containing the other! 4369 Exactly one network There are used several FBD resp. LD networks for a required for a transition transition. Please reduce to 1 network. 4370 Additional lines found Remove the not needed lines at the end of the transition. after correct ILtransition 4371 Invalid characters Remove the not needed characters at the end of the following valid transition. expression: ' 4400 Import / conversion of The POU cannot be converted to IEC 61131-3 completely. POU '%s' contains errors resp. is not complete. 4401 S5 time constant %lu There is no valid BCD coded time in the accu. seconds is too big (max. 9990s). 4402 Direct access to I/Os Make sure that you only access variables which are defined allowed only. as input or output. 4403 STEP5/7 instruction Some STEP5/7 commands are not convertable to IEC invalid or not 61131-3, e.g. CPU commands like MAS. convertible to IEC 61131-3. 4404 STEP5/7 operand Some STEP5/7 operands are not convertable to IEC 61131- invalid or not 3 respectively an operand is missing. convertible to IEC 61131-3. 4405 Reset of a STEP5/7 The corresponding IEC timer have no reset input. timer cannot be converted into IEC 61131-3. 4406 STEP5/7 Counter There is no valid BCD coded counter constant in the accu. constant out of range (max. 999). 4407 STEP5 instruction not Some STEP5/7 instructions cannot be converted to IEC convertible to IEC 61131-3, e.g. DUF. 61131-3. 4408 Bit access of timer or Special timer/counter commands are not convertable into counter words not IEC 61131-3. convertible into IEC 61131-3. 4409 Contents of ACCU1 or A command, which connects the both accus, cannot be <strong>BRESIMAR</strong> Anexo B – 15 de 18
Page 1:
2009-01-12 mpro_twcplc.pdf (v1.2) B
Page 5 and 6:
TWINCAT PLC - Tipo de Dados e Varia
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
TWINCAT PLC - Lista de Instruções
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
TWINCAT PLC - Funções bloco “st
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
TWINCAT PLC - Funções “standard
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
TWINCAT PLC - Exemplos práticos BE
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60: TWINCAT PLC - Exemplos práticos BE
Page 87 and 88: TWINCAT PLC - Resumo de Instruçõe
Page 97 and 98: TWINCAT PLC - Lista de erros BECKHO
Page 109: TWINCAT PLC - Lista de erros BECKHO
Page 113 and 114: TWINCAT PLC - Lista de erros 4501 E
show all

BRESIMAR(asaTek)-Beckhoff-Livro Formação Técnica TwinCAT 2

Create successful ePaper yourself

Delete template?

Save as template?