Complete Material Standards Manual - Gainesville Regional Utilities

Table of Contents
Plug, SDR-35, Push-On (Gasketed), 6/10/2009.................................P-35.00
Primer, PVC, 6/10/2009......................................................P-50.00
Probe, Level, 6/10/2009.....................................................P-60.00
Reducer, DI, Cement Lined, MJ x MJ, 6/10/2009...............................R-10.00
Reducer, DI, Cement Lined, LEMJ x PE, 6/10/2009.............................R-10.10
Reducer, DI, Cement Lined, PE x SEMJ, 6/10/2009.............................R-10.20
Reducer, DI, Cement Lined, PE x PE, 6/10/2009...............................R-10.30
Resetter, Meter with Backflow Preventer, 6/10/2009..........................R-21.00
Restraint, Megalug, Split, DI, 9/18/2009....................................R-25.00
Restraint, Megalug, Push on pipe, DI, 9/21/2009.............................R-26.00
Restraining Rod & Accessories, Galvanized, 6/10/2009........................R-30.00
Riser, Manhole Section, 6/10/2009...........................................R-50.00
Saddle, Service, DI Pipe, CC Thread, 6/10/2009..............................S-10.00
Saddle, Service, DI Pipe, NPT Thread Outlet, 6/10/2009......................S-10.10
Saddle, Service, Stainless, IP Thread Outlet, 10/12/2009....................S-10.20
Saddle, Service, Galvanized Pipe, CC Thread, 6/10/2009......................S-11.00
Saddle, Service, Galvanized Pipe, NPT Thread, 6/10/2009.....................S-11.10
Saddle, Service, Schedule 40 PVC Pipe, CC Thread, 6/10/2009.................S-12.00
Sand, Wellpoint, 6/10/2009..................................................S-20.00
Sealant, Manhole Joint, 6/10/2009...........................................S-30.00
Sealant, Thread, Paste Type, 6/10/2009......................................S-31.00
Sealant, Thread, Teflon Tape, 6/10/2009.....................................S-32.00
Sleeve, Solid, Epoxy Lined, MJ x MJ, 6/10/2009..............................S-40.00
Sleeve, Solid, MJ x MJ (4"-12"), 6/10/2009..................................S-41.00
Sleeve, Solid, MJ x MJ (14"-36"), 6/10/2009.................................S-41.01
Sleeve, Tapping, DI/PVC, 6/10/2009..........................................S-43.00
Sleeve, Tapping, Stainless Steel, MJ (4"-12"), 6/10/2009....................S-44.00
Sleeve, Tapping, Stainless Steel, MJ (16"-24"), 6/10/2009...................S-44.01
Sleeve, Tapping, Stainless, Flange (6" - 36"), 10/12/2009...................S-45.00
Tee, Brass, Threaded, 6/10/2009.............................................T-20.00
Tee, DI, Cement Lined, Anchoring, MJ-Swivel, 6/10/2009......................T-21.00
Tee, DI, Cement Lined, Bullhead, FL x FL x FL, 6/10/2009....................T-22.00
Tee, DI, Cement Lined, MJ x MJ x MJ (4"-16"), 6/10/2009.....................T-23.00
Tee, DI, Cement Lined, MJ x MJ x MJ (20"-24"), 6/10/2009....................T-23.10
Tee, PVC, SCH 40, Solvent Weld, 6/10/2009...................................T-25.00