Setup and Assembling Bookeye 3 - Image Access Inc.

More documents

Recommendations

Info

A.2.3 Assembling the Glass Plate Insert the book cradle plates into the driving elements and place the foam rubber mats on the plates. Connect the scanner to the mains power and switch it on with the main power switch. The main power switch is found on the rear side of the scanner, next to the power connector. The green START LED on the keyboard lights up. This signalizes that the scanner is in stand-by mode. Press the green START button to start the scanner. When the start sequence is finished after approximately 30 seconds, the display shows: READY TO SCAN The book cradle plates are controlled by the eight buttons in the middle of the keyboard field. Picture 30: Book cradle controller Press and hold the upper button with the double arrow to move both book cradle plates upwards simultaneously. At the upper end position, the book cradle motors stop automatically. Place the glass plate on the book cradle plates. The position of the bearing in the middle of the glass plate must match with the boreholes in the black cover. Insert two Allen screws, M8x12, into the bearing and fix it to the camera neck. Picture 31: Bearing in the center of the glass plate Page 28 Setup and Assembly Manual
Place the T-slot nuts in each lamp at a position corresponding to the position of the axes at the right and left side of the glass plate. Picture 32: T-slot nut in corresponding position Slide a hinge on each axis. Fix each hinge to the lamp with an Allen screw M8x12. Picture 33: Hinge mounted at right lamp Setup and Assembly Manual Page 29
Page 1 and 2: Version R1 Setup and Assembly Manua
Page 3 and 4: Introduction Dear Customer, We cong
Page 5 and 6: Version History Version Published i
Page 7 and 8: Table of Contents, part 2 B Softwar
Page 9 and 10: Table of Pictures Picture 1: Transp
Page 11 and 12: Setup and Assembly Manual Page 11
Page 13 and 14: On the cardboard separator are plac
Page 15 and 16: A.1.1 Tools and Assembling Material
Page 17 and 18: A.1.2.3 Scanner Table Place the dev
Page 19 and 20: Place the T-slot nuts in the neck c
Page 21 and 22: A.2.2 Assembling Lamps and Camera t
Page 23 and 24: Picture 18: Remove marked screws Re
Page 25 and 26: Before inserting the camera neck in
Page 27: Slide the body element cover slowly
Page 31 and 32: Open the glass plate completely, ho
Page 33 and 34: A.2.4 Setting the Initial Lamp Posi
Page 35 and 36: If the lamps are in their start pos
Page 37 and 38: The two screw head caps at the uppe
Page 39 and 40: B Software Setup B.1 Setup Network
Page 41 and 42: Now change the IP address, subnet m
Page 43 and 44: All adjustments described in chapte
Page 45 and 46: B.2.1 Scan Start This function adju
Page 47 and 48: B.2.2 Auto Focus This function auto
Page 49 and 50: Picture 57: Auto Focus results 5. C
Page 51 and 52: When the book cradles are in the up
Page 53 and 54: B.2.4 White Balance B.2.4.1 Some Ba
Page 55 and 56: B.2.4.2 White Balance with Glass Pl
Page 57 and 58: B.2.4.3 White Balance with Glass Pl
Page 59 and 60: 4. After the function has finished,
Page 61 and 62: B.3.2 Sound Control Locate the sect
Page 63 and 64: B.3.4 Install Options Locate the se
Page 65 and 66: C Tests and Troubleshooting C.1 Net
Page 67 and 68: C.2 Scan Test Targets The scanner h
Page 69 and 70: C.3 Recovery Function The recovery
Page 71 and 72: C.4 Troubleshooting Matrix Problem
Page 73 and 74: C.5 Error Codes The scanner does re
Page 75 and 76: Error # Error message shown in Erro
Page 77 and 78: D.3 Electrical Specifications This
Page 79:
Notes Setup and Assembly Manual Pag
show all

Setup and Assembling Bookeye 3 - Image Access Inc.

Create successful ePaper yourself

Delete template?

Save as template?