Setup and Assembling Bookeye 3 - Image Access Inc.

More documents

Recommendations

Info

B.2.2.1 Auto Focus Measurement with Glass Plate Opened Perform the measurement as follows: 3. Open the scanner’s book cradle completely, as shown on the screen. Note: The position of the book cradles is verified. If the book cradles are not in the lowest (home) position, a Retry button and a message are displayed on the screen instead of the Next Step button . 4. Press the Next Step button. The measurement starts. Picture 56: Auto Focus measurement with open glass plate After the Autofocus function has completed, the results will be displayed. Values displayed in green indicate valid results. Any error will be shown in red text, followed by some explanatory remarks. Note: It is normal that the measurement will return different values each time the measurement is repeated. The lens motor has a very high resolution and the best focal point has to be found in the already large focal range, therefore a variation of 50 – 100 in values is normal. Page 48 Setup and Assembly Manual
Picture 57: Auto Focus results 5. Click the button New Values in the section Controls to repeat the measurement. Or 6. Click the button Back to Adj. Menu in the section Menu controls to return to the adjustments menu (see Picture 52). Setup and Assembly Manual Page 49
Page 1 and 2: Version R1 Setup and Assembly Manua
Page 3 and 4: Introduction Dear Customer, We cong
Page 5 and 6: Version History Version Published i
Page 7 and 8: Table of Contents, part 2 B Softwar
Page 9 and 10: Table of Pictures Picture 1: Transp
Page 11 and 12: Setup and Assembly Manual Page 11
Page 13 and 14: On the cardboard separator are plac
Page 15 and 16: A.1.1 Tools and Assembling Material
Page 17 and 18: A.1.2.3 Scanner Table Place the dev
Page 19 and 20: Place the T-slot nuts in the neck c
Page 21 and 22: A.2.2 Assembling Lamps and Camera t
Page 23 and 24: Picture 18: Remove marked screws Re
Page 25 and 26: Before inserting the camera neck in
Page 27 and 28: Slide the body element cover slowly
Page 29 and 30: Place the T-slot nuts in each lamp
Page 31 and 32: Open the glass plate completely, ho
Page 33 and 34: A.2.4 Setting the Initial Lamp Posi
Page 35 and 36: If the lamps are in their start pos
Page 37 and 38: The two screw head caps at the uppe
Page 39 and 40: B Software Setup B.1 Setup Network
Page 41 and 42: Now change the IP address, subnet m
Page 43 and 44: All adjustments described in chapte
Page 45 and 46: B.2.1 Scan Start This function adju
Page 47: B.2.2 Auto Focus This function auto
Page 51 and 52: When the book cradles are in the up
Page 53 and 54: B.2.4 White Balance B.2.4.1 Some Ba
Page 55 and 56: B.2.4.2 White Balance with Glass Pl
Page 57 and 58: B.2.4.3 White Balance with Glass Pl
Page 59 and 60: 4. After the function has finished,
Page 61 and 62: B.3.2 Sound Control Locate the sect
Page 63 and 64: B.3.4 Install Options Locate the se
Page 65 and 66: C Tests and Troubleshooting C.1 Net
Page 67 and 68: C.2 Scan Test Targets The scanner h
Page 69 and 70: C.3 Recovery Function The recovery
Page 71 and 72: C.4 Troubleshooting Matrix Problem
Page 73 and 74: C.5 Error Codes The scanner does re
Page 75 and 76: Error # Error message shown in Erro
Page 77 and 78: D.3 Electrical Specifications This
Page 79: Notes Setup and Assembly Manual Pag

Setup and Assembling Bookeye 3 - Image Access Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?