Setup and Assembling Bookeye 3 - Image Access Inc.

More documents

Recommendations

Info

3. Place the White Reference Target 225x670 at the marked position. Picture 64: White Balance screen, glass plate opened 4. Press the Next Step button. The measurement starts. After the Autofocus function has completed, the results will be displayed. Values displayed in green indicate valid results. Any error will be shown in red text, followed by some explanatory remarks. 5. Click the button Back to Adjustment Menu to return to the adjustments menu. Page 56 Setup and Assembly Manual
B.2.4.3 White Balance with Glass Plate closed Start in the Adjustments & Support screen (Picture 52). Perform the measurement as follows: 1. Find the section White Balance Adjustments and click the button White Balance . Press the Next Step button below the picture corresponding to the selected glass plate position. Picture 63 shows the available positions of the glass plate. 2. Close the book cradles completely and move them to the upper position. Note: The position of the book cradles is verified. If the book cradles are not in the upper position a Retry button and a message are displayed on the screen instead of the Next Step button. After moving the book cradles to the upper position, press the Retry button. 3. Place the White Reference Target 225x670 at the marked position. 4. Press the Next Step button. Picture 65: White Balance screen, glass plate closed After the Autofocus function has completed, the results will be displayed. Values displayed in green indicate valid results. Any error will be shown in red text, followed by some explanatory remarks. 5. Click the button Back to Adjustment Menu to return to the adjustments menu. Setup and Assembly Manual Page 57
Page 1 and 2:
Version R1 Setup and Assembly Manua
Page 3 and 4:
Introduction Dear Customer, We cong
Page 5 and 6: Version History Version Published i
Page 7 and 8: Table of Contents, part 2 B Softwar
Page 9 and 10: Table of Pictures Picture 1: Transp
Page 11 and 12: Setup and Assembly Manual Page 11
Page 13 and 14: On the cardboard separator are plac
Page 15 and 16: A.1.1 Tools and Assembling Material
Page 17 and 18: A.1.2.3 Scanner Table Place the dev
Page 19 and 20: Place the T-slot nuts in the neck c
Page 21 and 22: A.2.2 Assembling Lamps and Camera t
Page 23 and 24: Picture 18: Remove marked screws Re
Page 25 and 26: Before inserting the camera neck in
Page 27 and 28: Slide the body element cover slowly
Page 29 and 30: Place the T-slot nuts in each lamp
Page 31 and 32: Open the glass plate completely, ho
Page 33 and 34: A.2.4 Setting the Initial Lamp Posi
Page 35 and 36: If the lamps are in their start pos
Page 37 and 38: The two screw head caps at the uppe
Page 39 and 40: B Software Setup B.1 Setup Network
Page 41 and 42: Now change the IP address, subnet m
Page 43 and 44: All adjustments described in chapte
Page 45 and 46: B.2.1 Scan Start This function adju
Page 47 and 48: B.2.2 Auto Focus This function auto
Page 49 and 50: Picture 57: Auto Focus results 5. C
Page 51 and 52: When the book cradles are in the up
Page 53 and 54: B.2.4 White Balance B.2.4.1 Some Ba
Page 55: B.2.4.2 White Balance with Glass Pl
Page 59 and 60: 4. After the function has finished,
Page 61 and 62: B.3.2 Sound Control Locate the sect
Page 63 and 64: B.3.4 Install Options Locate the se
Page 65 and 66: C Tests and Troubleshooting C.1 Net
Page 67 and 68: C.2 Scan Test Targets The scanner h
Page 69 and 70: C.3 Recovery Function The recovery
Page 71 and 72: C.4 Troubleshooting Matrix Problem
Page 73 and 74: C.5 Error Codes The scanner does re
Page 75 and 76: Error # Error message shown in Erro
Page 77 and 78: D.3 Electrical Specifications This
Page 79: Notes Setup and Assembly Manual Pag
show all

Setup and Assembling Bookeye 3 - Image Access Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?