Setup and Assembling Bookeye 3 - Image Access Inc.

More documents

Recommendations

Info

B.2 Mandatory Optical Adjustments Whenever the device is setup for the first time, moved to a different location, cleaned or serviced and after a software update; some adjustments have to be performed to guarantee maximum quality and accuracy. Access to these functions is only possible through the login level “Poweruser”, default password “Poweruser”. The person having access to this level can change the password and thereby limit access to normal operators. The following functions use special test targets that were supplied with the scanner. Do not try to perform any of these adjustments without the proper test targets. The Bookeye ® 3 scanner is delivered with the following test targets: — White Reference Target 110x670 — Line Reference Sheet LRS-200 Please ensure that adjustments are made following the sequence below. 1. Perform the Scan Start function. This will synchronize the CCD main drive motor with the lamp motors so that the CCD is centered along the horizontal axis and the lamp beams follow as precisely as possible. 2. Execute the Auto Focus function to establish a basic reference for the focus motor. This function should also be invoked any time the scanner seems to be out of focus. 3. The next step is the White Balance function. This calibrates the scanner’s CCD and optics relative to the lamp light and the remaining ambient light. This function should be invoked if the brightness seems to have shifted, the ambient light situation has changed significantly or the images have horizontal stripes on them. 4. The next step is the Laser Check function. This function checks all properties of the laser line and will return overall skew and position of the laser line. Page 42 Setup and Assembly Manual
All adjustments described in chapter B.2 and its subchapters start from the main screen of the login level ”Poweruser”. Start your browser software. Enter the IP address of the scanner in your browser to open the start menu. In the start screen go to Setup Device . Picture 49: Scan2Net Start screen Choose the login level Poweruser using the default password "Poweruser". Picture 50: Buttons for login levels The next screen shows the main menu screen. Setup and Assembly Manual Page 43
Page 1 and 2: Version R1 Setup and Assembly Manua
Page 3 and 4: Introduction Dear Customer, We cong
Page 5 and 6: Version History Version Published i
Page 7 and 8: Table of Contents, part 2 B Softwar
Page 9 and 10: Table of Pictures Picture 1: Transp
Page 11 and 12: Setup and Assembly Manual Page 11
Page 13 and 14: On the cardboard separator are plac
Page 15 and 16: A.1.1 Tools and Assembling Material
Page 17 and 18: A.1.2.3 Scanner Table Place the dev
Page 19 and 20: Place the T-slot nuts in the neck c
Page 21 and 22: A.2.2 Assembling Lamps and Camera t
Page 23 and 24: Picture 18: Remove marked screws Re
Page 25 and 26: Before inserting the camera neck in
Page 27 and 28: Slide the body element cover slowly
Page 29 and 30: Place the T-slot nuts in each lamp
Page 31 and 32: Open the glass plate completely, ho
Page 33 and 34: A.2.4 Setting the Initial Lamp Posi
Page 35 and 36: If the lamps are in their start pos
Page 37 and 38: The two screw head caps at the uppe
Page 39 and 40: B Software Setup B.1 Setup Network
Page 41: Now change the IP address, subnet m
Page 45 and 46: B.2.1 Scan Start This function adju
Page 47 and 48: B.2.2 Auto Focus This function auto
Page 49 and 50: Picture 57: Auto Focus results 5. C
Page 51 and 52: When the book cradles are in the up
Page 53 and 54: B.2.4 White Balance B.2.4.1 Some Ba
Page 55 and 56: B.2.4.2 White Balance with Glass Pl
Page 57 and 58: B.2.4.3 White Balance with Glass Pl
Page 59 and 60: 4. After the function has finished,
Page 61 and 62: B.3.2 Sound Control Locate the sect
Page 63 and 64: B.3.4 Install Options Locate the se
Page 65 and 66: C Tests and Troubleshooting C.1 Net
Page 67 and 68: C.2 Scan Test Targets The scanner h
Page 69 and 70: C.3 Recovery Function The recovery
Page 71 and 72: C.4 Troubleshooting Matrix Problem
Page 73 and 74: C.5 Error Codes The scanner does re
Page 75 and 76: Error # Error message shown in Erro
Page 77 and 78: D.3 Electrical Specifications This
Page 79: Notes Setup and Assembly Manual Pag

Setup and Assembling Bookeye 3 - Image Access Inc.

Create successful ePaper yourself

Delete template?

Save as template?