Setup and Assembling Bookeye 3 - Image Access Inc.

More documents

Recommendations

Info

Each gas spring has on its ends special locking springs inserted. Important: The locking springs always must be removed before placing or removing the gas springs at the glass plate or on the pin at the lamps. Picture 34: Position of locking springs Picture 34 shows the position of the locking springs at the lamp and at the glass plate. When the scanner is delivered, the gas springs are already mounted to the lamps. They only must be mounted to the glass plate. To mount the gas springs to the glass plate, remove only the locking spring at the glass plate side of the gas spring. At first turn the locking spring (1.) over the ball head of the gas spring. It needs a little force to move the spring over the ball head. Then pull it out of the boreholes (2.). Picture 35: Removing the locking spring Page 30 Setup and Assembly Manual
Open the glass plate completely, hold it in this position and click the gas spring onto the pin of the glass plate. Picture 36: Gas spring mounted to glass plate Repeat the procedure with the second gas spring. Finally insert the locking springs at both gas springs. Picture 37: Locking spring inserted Picture 38: Locking spring locked Setup and Assembly Manual Page 31
Page 1 and 2: Version R1 Setup and Assembly Manua
Page 3 and 4: Introduction Dear Customer, We cong
Page 5 and 6: Version History Version Published i
Page 7 and 8: Table of Contents, part 2 B Softwar
Page 9 and 10: Table of Pictures Picture 1: Transp
Page 11 and 12: Setup and Assembly Manual Page 11
Page 13 and 14: On the cardboard separator are plac
Page 15 and 16: A.1.1 Tools and Assembling Material
Page 17 and 18: A.1.2.3 Scanner Table Place the dev
Page 19 and 20: Place the T-slot nuts in the neck c
Page 21 and 22: A.2.2 Assembling Lamps and Camera t
Page 23 and 24: Picture 18: Remove marked screws Re
Page 25 and 26: Before inserting the camera neck in
Page 27 and 28: Slide the body element cover slowly
Page 29: Place the T-slot nuts in each lamp
Page 33 and 34: A.2.4 Setting the Initial Lamp Posi
Page 35 and 36: If the lamps are in their start pos
Page 37 and 38: The two screw head caps at the uppe
Page 39 and 40: B Software Setup B.1 Setup Network
Page 41 and 42: Now change the IP address, subnet m
Page 43 and 44: All adjustments described in chapte
Page 45 and 46: B.2.1 Scan Start This function adju
Page 47 and 48: B.2.2 Auto Focus This function auto
Page 49 and 50: Picture 57: Auto Focus results 5. C
Page 51 and 52: When the book cradles are in the up
Page 53 and 54: B.2.4 White Balance B.2.4.1 Some Ba
Page 55 and 56: B.2.4.2 White Balance with Glass Pl
Page 57 and 58: B.2.4.3 White Balance with Glass Pl
Page 59 and 60: 4. After the function has finished,
Page 61 and 62: B.3.2 Sound Control Locate the sect
Page 63 and 64: B.3.4 Install Options Locate the se
Page 65 and 66: C Tests and Troubleshooting C.1 Net
Page 67 and 68: C.2 Scan Test Targets The scanner h
Page 69 and 70: C.3 Recovery Function The recovery
Page 71 and 72: C.4 Troubleshooting Matrix Problem
Page 73 and 74: C.5 Error Codes The scanner does re
Page 75 and 76: Error # Error message shown in Erro
Page 77 and 78: D.3 Electrical Specifications This
Page 79: Notes Setup and Assembly Manual Pag

Setup and Assembling Bookeye 3 - Image Access Inc.

Create successful ePaper yourself

Delete template?

Save as template?