Setup and Assembling Bookeye 3 - Image Access Inc.

More documents

Recommendations

Info

B.3.5 Install ICC Profiles Locate the section Updates & Uploads and go to ICC Profiles . Picture 73: ICC Profile screen Select either Printer Profiles or Scanner Profile . In the next screen, browse for a new ICC profile and select it. It will replace the previous file. Page 64 Setup and Assembly Manual
C Tests and Troubleshooting C.1 Network Performance Test It is sometimes desirable to check network performance if the scanner seems to be operating slowly. The scanner itself has a gigabit network interface and can transfer data at a sustained rate of almost 100Mbytes per second. This is far more than most standard PCs can handle and comes very close to the maximum bandwidth of the gigabit network. If the scanner runs in a 100Mbit networks it is already slowed down significantly, particularly if the file sizes are large. Sometimes the network’s response times are poor because routers and/or switches with slow performance are used, or the topology of the network is not optimal. This analyzer checks the response time between the scanner and any arbitrary IP address in the network. In most cases, the IP address would be the one from the PC operating the scanner, but FTP links can also be checked via this function. Perform the test as follows: Locate the section Adjustments & Support and go to Network Analyzer . Go to Perform Speed Test . Picture 74: Perform Speed Test screen Setup and Assembly Manual Page 65
Page 1 and 2:
Version R1 Setup and Assembly Manua
Page 3 and 4:
Introduction Dear Customer, We cong
Page 5 and 6:
Version History Version Published i
Page 7 and 8:
Table of Contents, part 2 B Softwar
Page 9 and 10:
Table of Pictures Picture 1: Transp
Page 11 and 12:
Setup and Assembly Manual Page 11
Page 13 and 14: On the cardboard separator are plac
Page 15 and 16: A.1.1 Tools and Assembling Material
Page 17 and 18: A.1.2.3 Scanner Table Place the dev
Page 19 and 20: Place the T-slot nuts in the neck c
Page 21 and 22: A.2.2 Assembling Lamps and Camera t
Page 23 and 24: Picture 18: Remove marked screws Re
Page 25 and 26: Before inserting the camera neck in
Page 27 and 28: Slide the body element cover slowly
Page 29 and 30: Place the T-slot nuts in each lamp
Page 31 and 32: Open the glass plate completely, ho
Page 33 and 34: A.2.4 Setting the Initial Lamp Posi
Page 35 and 36: If the lamps are in their start pos
Page 37 and 38: The two screw head caps at the uppe
Page 39 and 40: B Software Setup B.1 Setup Network
Page 41 and 42: Now change the IP address, subnet m
Page 43 and 44: All adjustments described in chapte
Page 45 and 46: B.2.1 Scan Start This function adju
Page 47 and 48: B.2.2 Auto Focus This function auto
Page 49 and 50: Picture 57: Auto Focus results 5. C
Page 51 and 52: When the book cradles are in the up
Page 53 and 54: B.2.4 White Balance B.2.4.1 Some Ba
Page 55 and 56: B.2.4.2 White Balance with Glass Pl
Page 57 and 58: B.2.4.3 White Balance with Glass Pl
Page 59 and 60: 4. After the function has finished,
Page 61 and 62: B.3.2 Sound Control Locate the sect
Page 63: B.3.4 Install Options Locate the se
Page 67 and 68: C.2 Scan Test Targets The scanner h
Page 69 and 70: C.3 Recovery Function The recovery
Page 71 and 72: C.4 Troubleshooting Matrix Problem
Page 73 and 74: C.5 Error Codes The scanner does re
Page 75 and 76: Error # Error message shown in Erro
Page 77 and 78: D.3 Electrical Specifications This
Page 79: Notes Setup and Assembly Manual Pag
show all

Setup and Assembling Bookeye 3 - Image Access Inc.

Create successful ePaper yourself

Delete template?

Save as template?