download - Knoll

Currents worksurfaces for Morrison
straight, flat front
3/8 wire drop and grommet
Morrison
description w d h pattern no. lam.
24D - Straight worksurface, flat front 24 23 5 /8 1 AWM2 F2424 ( )( ) $277.
30 23 5 /8 1 AWM2 F3024 ( )( ) 304.
36 23 5 /8 1 AWM2 F3624 ( )( ) 332.
42 23 5 /8 1 AWM2 F4224 ( )( ) 362.
48 23 5 /8 1 AWM2 F4824 ( )( ) 387.
54 23 5 /8 1 AWM2 F5424 ( )( ) 414.
60 23 5 /8 1 AWM2 F6024 ( )( ) 442.
66 23 5 /8 1 AWM2 F6624 ( )( ) 471.
72 23 5 /8 1 AWM2 F7224 ( )( ) 500.
78 23 5 /8 1 AWM2 F7824 ( )( ) 524.
84 23 5 /8 1 AWM2 F8424 ( )( ) 554.
90 23 5 /8 1 AWM2 F9024 ( )( ) 580.
96 23 5 /8 1 AWM2 F9624 ( )( ) 610.
30D - Straight worksurface, flat front 30 29 5 /8 1 AWM2 F3030 ( )( ) 345.
36 29 5 /8 1 AWM2 F3630 ( )( ) 374.
42 29 5 /8 1 AWM2 F4230 ( )( ) 404.
48 29 5 /8 1 AWM2 F4830 ( )( ) 427.
54 29 5 /8 1 AWM2 F5430 ( )( ) 462.
60 29 5 /8 1 AWM2 F6030 ( )( ) 500.
66 29 5 /8 1 AWM2 F6630 ( )( ) 541.
72 29 5 /8 1 AWM2 F7230 ( )( ) 581.
78 29 5 /8 1 AWM2 F7830 ( )( ) 622.
84 29 5 /8 1 AWM2 F8430 ( )( ) 647.
90 29 5 /8 1 AWM2 F9030 ( )( ) 706.
96 29 5 /8 1 AWM2 F9630 ( )( ) 746.
Worksurface Planning
Order Code
Specification Information
Application Notes
Example: AWM2 F4830-119-119
AWM2 Worksurface
F Flat
48 Width
30 Depth
119 Top finish
119 Trim finish
Specify top finish first, followed by
trim finish.
Please refer to the Currents price
list for finishes.
Veneer finishes for Currents
worksurfaces for Morrison are
available through Custom Product
Development.
Worksurfaces are sized for Morrison
panel-based applications and may
be supported by Morrison panel
planning brackets or end-supported
from Currents wall. 24D straight
tops may also be cantilevered from
Currents service wall. Underside of
worksurfaces is drilled to accept all
Morrison panel-planning brackets,
Morrison and Currents pedestals,
and worksurface stiffeners. 24D
straight tops are also drilled to
accept Currents wall cantilever
brackets. AWM2- worksurfaces are
supported by brackets with wood
screws.
When using Morrison end support
brackets, order MB3-EC18, 24 or
30.
Currents worksurfaces for Morrison
require stiffener when the span
between structural supports exceeds
36. Specify worksurface stiffeners
and supports separately (page 142).
Flat front allows two straight
worksurfaces to meet at right angles.
Actual worksurface depth is 3 /8 less
than nominal 24 and 30 for cable
clearance.
All worksurfaces include one edge
grommet, centered at rear of
worksurface, with maximum
clearance of 1 5 /8.
Currents for Morrison worksurfaces
feature crisp, 90-degree corners
eliminating the corner kick detail
typical of Currents universal
worksurfaces. This facilitates the
use of brackets, pedestals and end
panels at the side edge of
worksurfaces.
Currents worksurfaces for Morrison
cannot be used in conjunction with
Morrison Network desk supports.
137