download - Knoll

Currents worksurfaces for Morrison
extended corner
3/8 wire drop and grommet
extended right
description w d h pattern no. lam.
24D both sides - Corner worksurfaces extended
right
Morrison
36 60 1 AWM2 C3660 S ( )( ) $685.
36 72 1 AWM2 C3672 S ( )( ) 824.
42 60 1 AWM2 C4260 S ( )( ) 756.
42 72 1 AWM2 C4272 S ( )( ) 889.
48 60 1 AWM2 C4860 S ( )( ) 824.
48 72 1 AWM2 C4872 S ( )( ) 958.
48 84 1 AWM2 C4884 S ( )( ) 1,096.
30D both sides - Corner worksurfaces extended
right
48 60 1 AWM2 C4860 D ( )( ) 891.
48 72 1 AWM2 C4872 D ( )( ) 1,027.
48 84 1 AWM2 C4884 D ( )( ) 1,165.
24D left/30D right - Corner worksurfaces
extended right
30D left/24D right - Corner worksurfaces
extended right
42 60 1 AWM2 C4260 R ( )( ) 824.
42 72 1 AWM2 C4272 R ( )( ) 958.
48 60 1 AWM2 C4860 R ( )( ) 891.
48 72 1 AWM2 C4872 R ( )( ) 1,027.
48 84 1 AWM2 C4884 R ( )( ) 1,165.
42 60 1 AWM2 C4260 L ( )( ) 824.
42 72 1 AWM2 C4272 L ( )( ) 958.
48 60 1 AWM2 C4860 L ( )( ) 891.
48 72 1 AWM2 C4872 L ( )( ) 1,027.
48 84 1 AWM2 C4884 L ( )( ) 1,165.
Order Code
Specification Information
Application Notes
Example: AWM2 C3660S-119-119
AWM2 Worksurface
C Corner
36 Width left
60 Width right
S Depth left and right
119 Top finish
119 Trim finish
Dimensions shown in ‘‘w’’ column
are nominal width of left back edge.
Dimensions shown in ‘‘d’’ column
are nominal width of right back
edge.
Worksurface depths:
S 24D both sides
L 30D left/24D right
R 24D left/30D right
Specify top finish first, followed by
trim finish.
Please refer to the Currents price
list for finishes.
Veneer finishes for Currents
worksurfaces for Morrison are
available through Custom Product
Development.
Worksurfaces are sized for Morrison
panel-based applications and may
be supported by Morrison
panel-planning brackets or
end-supported and cantilevered
from Currents wall. Extended side
may also be supported with Currents
C-legs. Underside of worksurface is
drilled to accept all Morrison
panel-planning brackets, Morrison
and Currents pedestals, worksurface
stiffeners and Currents C-leg on the
extended side.
AWM2- worksurfaces are supported
by brackets with wood screws.
When using Morrison end support
brackets, order MB3-EC18, 24 or
30.
Currents worksurfaces for Morrison
require stiffener when the span
between structural supports exceeds
36. Specify worksurface stiffeners
and supports separately (page 142).
Currents worksurfaces for Morrison
cannot be used in conjunction with
Morrison Network desk supports.
Actual worksurface is 3 /8 less than
nominal 24 and 30 for cable
clearance.
All worksurfaces include two edge
grommets, centered on back edges
of worksurface, with maximum
clearance of 1 5/8.
140