download - Knoll

Currents worksurfaces for Morrison
extended corner
3/8 wire drop and grommet
extended left
description w d h pattern no. lam.
24D both sides - Corner worksurfaces, extended
left
Morrison
60 36 1 AWM2 C6036 S ( )( ) $685.
60 42 1 AWM2 C6042 S ( )( ) 756.
60 48 1 AWM2 C6048 S ( )( ) 824.
72 36 1 AWM2 C7236 S ( )( ) 824.
72 42 1 AWM2 C7242 S ( )( ) 889.
72 48 1 AWM2 C7248 S ( )( ) 958.
84 48 1 AWM2 C8448 S ( )( ) 1,096.
30D both sides - Corner worksurfaces, extended
left
60 48 1 AWM2 C6048 D ( )( ) 891.
72 48 1 AWM2 C7248 D ( )( ) 1,027.
84 48 1 AWM2 C8448 D ( )( ) 1,165.
24D left/30D right - Corner worksurfaces,
extended left
30D left/24D right - Corner worksurfaces,
extended left
60 42 1 AWM2 C6042 R ( )( ) 824.
60 48 1 AWM2 C6048 R ( )( ) 891.
72 42 1 AWM2 C7242 R ( )( ) 958.
72 48 1 AWM2 C7248 R ( )( ) 1,027.
84 48 1 AWM2 C8448 R ( )( ) 1,165.
60 42 1 AWM2 C6042 L ( )( ) 824.
60 48 1 AWM2 C6048 L ( )( ) 891.
72 42 1 AWM2 C7242 L ( )( ) 958.
72 48 1 AWM2 C7248 L ( )( ) 1,027.
84 48 1 AWM2 C8448 L ( )( ) 1,165.
Worksurface Planning
Order Code
Specification Information
Application Notes
Example: AWM2 C6036S119-119
AWM2 Worksurface
C Corner
60 Width left
36 Width right
S Depth left and right
119 Top finish
119 Trim finish
Dimensions shown in ‘‘w’’ column
are nominal width of left back edge.
Dimensions shown in ‘‘d’’ column
are nominal width of right back
edge.
Worksurface depths:
S 24D both sides
L 30D left/24D right
R 24D left/30D right
Specify top finish first, followed by
trim finish.
Please refer to the Currents price
list for finishes.
Veneer finishes for Currents
worksurfaces for Morrison are
available through Custom Product
Development.
Worksurfaces are sized for Morrison
panel-based applications and may
be supported by Morrison
panel-planning brackets or
end-supported and cantilevered
from Currents wall. Extended side
may also be supported with Currents
C-legs. Underside of worksurface is
drilled to accept all Morrison
panel-planning brackets, Morrison
and Currents pedestals, worksurface
stiffeners and Currents C-leg on the
extended side.
AWM2- worksurfaces are supported
by brackets with wood screws.
When using Morrison end support
brackets, order MB3-EC18, 24 or
30.
Currents worksurfaces for Morrison
require stiffener when the span
between structural supports exceeds
36. Specify worksurface stiffeners
and supports separately (page 142).
Currents worksurfaces for Morrison
cannot be used in conjunction with
Morrison Network desk supports.
Actual worksurface is 3 /8 less than
nominal 24 and 30 for cable
clearance.
All worksurfaces include two edge
grommets, centered on back edges
of worksurface, with maximum
clearance of 1 5/8.
139