ncr/doc/Kiosks/TechnicalManuals/7401_Kiosk_Har... - Alsys Data

More documents

Recommendations

Info

4-18 Chapter 4: 7401-4xxx Hardware Installation Installing a 7401-4xxx on a Table Top Mount A 7401‐4xxx terminal attached to a Table Top Mount can be installed on any flat work surface following the height guidelines shown in the NCR EasyPoint 7401 Site Preparation Guide (B005‐0000‐1255). Locking Slots Locating Locking Slots 19964 Mounting Procedures 1. Using the Table Top Mount as a template, position the Mount on the surface where the terminal is to be located and mark all hole locations with a pencil.
Chapter 4: 7401-4xxx Hardware Installation 4-19 To locate the 7401‐4xxx terminal so the edge of the Keyboard Tray is even with the edge of the table top, locate the front edge of the Table Top Mount 210 mm (8.25 in.) from the edge of the mounting surface. 2. Drill pilot holes or through holes for the mounting screws (4) or mounting bolts. Screws or bolts used for mounting the terminal are not provided with the mount and must be purchased locally. The holes in the mount are xx mm (xx in.) in diameter. 3. Drill the hole to route the cables out the bottom of the terminal, if using that cable routing solution. 4. Secure the Table Top Mount to the mounting surface. Note: When the front edge of the Table Top Mount is located away from the edge of the mounting surface, it may be necessary to remove the Motorized Card Reader, Keyboard, and Sliding Drawer assembly before placing the terminal onto the mount to provide access to the mounting screws. Refer to the “Accessing the Mounting Screws” section below for details. 5. Lower the terminal onto the Mount aligning the locking pins (4) on the bottom of the terminal with the slots in the mount. Caution: Use care when lifting the terminal. The 7401‐4xxx terminal weighs approximately 90 lbs. (40.8 kg). 6. Push the terminal to the back until the locating pins (2) in the back of terminal are fully engaged into the holes in the mount. 7. Secure the terminal to the mount using the 8x32 screws (2).
Page 1 and 2:
NCR NCR EasyPoint 7401 Release 2.5
Page 3 and 4:
i Safety Warnings Preface Audience
Page 5 and 6:
iii Grounding Instructions In the e
Page 7 and 8:
v Table of Contents Chapter 1: 7401
Page 9 and 10:
vii Compact Flash (Optional).......
Page 11 and 12:
ix Internal Speaker ...............
Page 13 and 14:
xi Calibration Using MicroTouch (Wi
Page 15 and 16:
xiii Setting Boot Options .........
Page 17 and 18:
xv NCR 7401‐21xx/31xx NT Operatin
Page 19 and 20:
xvii Revision Record Issue Date Rem
Page 21 and 22:
xix IEC & EN Laser Product Label CA
Page 23 and 24:
Chapter 1: 7401-2xxx/3xxx Product O
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67:
Page 70 and 71:
2-2 Chapter 2: 7401-4xxx Product Ov
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
2-10 Chapter 2: 7401-4xxx Product O
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 103 and 104:
Chapter 3: 7401-2xxx/3xxx Hardware
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130: Chapter 3: 7401-2xxx/3xxx Hardware
Page 163 and 164: Chapter 4: 7401-4xxx Hardware Insta
Page 179: Chapter 4: 7401-4xxx Hardware Insta
Page 193: Chapter 4: 7401-4xxx Hardware Insta
Page 196 and 197: 5-2 Chapter 5: Setup Entering Setup
Page 198 and 199: 5-4 Chapter 5: Setup Setting Passwo
Page 200 and 201: 5-6 Chapter 5: Setup Setting Memory
Page 202 and 203: 5-8 Chapter 5: Setup BIOS Default C
Page 204 and 205: 5-10 Chapter 5: Setup Memory Cache
Page 206 and 207: 5-12 Chapter 5: Setup System Temper
Page 208 and 209: 5-14 Chapter 5: Setup Continuous PO
Page 210 and 211: 5-16 Chapter 5: Setup Interrupts (7
Page 212 and 213: 5-18 Chapter 5: Setup BIOS Default
Page 214 and 215: 5-20 Chapter 5: Setup Cache Memory
Page 216 and 217: 5-22 Chapter 5: Setup System Temper
Page 218 and 219: 5-24 Chapter 5: Setup QuickBoot Mod
Page 220 and 221: 5-26 Chapter 5: Setup Interrupts (7
Page 222 and 223: 5-28 Chapter 5: Setup BIOS Default
Page 224 and 225: 5-30 Chapter 5: Setup Advanced Valu
Page 226 and 227: 5-32 Chapter 5: Setup Memory Map (7
Page 228 and 229: 6-2 Chapter 6: Operating System Rec
Page 230 and 231:
6-4 Chapter 6: Operating System Rec
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
6-10 Chapter 6: Operating System Re
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
7-2 Chapter 7: BIOS Updating Proced
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
8-2 Chapter 8: NCR 7401 7890/7892 S
Page 268 and 269:
8-4 Chapter 8: NCR 7401 7890/7892 S
Page 270 and 271:
8-6 Chapter 8: NCR 7401 7890/7892 S
Page 272 and 273:
A-2 Appendix A: Cables Corporate ID
Page 274 and 275:
B-2 Appendix B: Feature Kits 2. Sel
Page 276 and 277:
B-4 Appendix B: Feature Kits Kit Nu
Page 278 and 279:
B-6 Appendix B: Feature Kits Kit Nu
Page 280 and 281:
Index-2 Setting boot options, 5‐6
Page 282 and 283:
Index-4 OS Recovery from a Larger D
show all

ncr/doc/Kiosks/TechnicalManuals/7401_Kiosk_Har... - Alsys Data

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?