SVI-II Instruc Man.book - Fagerberg

More documents

Recommendations

Info

Configuration and Calibration Configuration with Pushbutton Display CONFIG CONFIGuration Menu CONFIG * Air to Menu + + + + + Charact Pressure Tight Shut-off Language Menu Units Menu Menu Menu * Setup + Press * to select option. Press + or - to accept and proceed to next menu item. Air to ....Menu ATO * ATC Select Air To Open (ATO) or Air To Close (ATC). Must match the actuator exactly. * Charact Menu LINEAR * EQ% 30:1 * EQ% 50:1 * Pressure Units Menu PSI * BAR * KPA Turn tight shutoff on or off to provide maximum actuator force at 0% Tight Shutoff Menu T.S. OFF T.S. ON * +/- * - + * * Language Menu * ENGLISH * FRENCH Select display language. EQ% CAMFX * QUICK50 * Select display units for pressure. Displays tight shutoff value if turned on. Press * to change T.S. ON/OFF status. Press + or - to enter new value. Press * to accept new value and proceed to next menu item. CUSTOM Figure 29 Configuration Pushbutton Guide 59
Masoneilan Dresser SVI II AP Instruction Manual Calibration Note: Always perform configuration before running calibration functions. Pilot Trim Valve Applications require the use of the Manual Stop calibration procedure. Do not run “Find Stops” or the ValVue 2.4 “Setup Wizard” on valves with Pilot Trim or damage to the valve will occur. Calibrating the SVI II AP Unit Using Pushbuttons To calibrate the SVI II AP (see Figure 30 “Calibration Pushbutton Guide” on page 62): 1. Observe the display following power-up. The SVI II AP will power up in the previously active mode either MANUAL or NORMAL (operating) mode. 2. If in NORMAL mode, the display will alternate between POS and SIGNAL indicating Normal mode. 3. If in MANUAL, the display will alternate between POS –M and SIG indicating MANUAL mode. 4. With MANUAL mode displayed, press * to select the MANUAL mode. 5. Press any key to enter MANUAL menu. 6. Press + to display SETUP. 7. Press * to enter SETUP mode. 8. In SETUP mode press * again; ↓CONFIG appears. Pressing + again brings ↓CALIB. 9. Select CALIB by pressing *. STOPS appears. 10. Press * to perform FIND STOPS 11. The valve moves full open and back to full closed. Observe all warnings. 12. Press * to cause the valve to stroke and to automatically calibrate valve travel. 13. After the STOPS procedure finishes, press + twice until TUNE appears. Calibration using Auto Tune To auto tune the SVI II AP: 1. Press * to begin the autoTUNE procedure. This takes 3 to 10 minutes and strokes the valve in large and small steps to set the PID parameters for best positioning response. 2. When autoTUNE proceeds, numerical messages display, indicating the procedure is working. 3. When autoTUNE is complete, it will display TUNE. 4. Press + repeatedly until ↑ SETUP appears. 5. Press * to return to SETUP menu ↓CALIB appears. DO NOT perform STOPS while the valve is controlling the process. 60
Page 2 and 3:
Warranty Items sold by Dresser, ®
Page 4 and 5:
Masoneilan Dresser SVI II AP-1 Inst
Page 6 and 7:
Mounting the SVI II AP on Rotary Va
Page 8 and 9:
Pushbuttons and Local Display for C
Page 10 and 11:
Pneumatic Cover Installation . . .
Page 12 and 13:
Figure 42 Double Acting Pneumatic R
Page 14 and 15:
Introduction 1 The SVI ® II AP (Sm
Page 16 and 17:
Introduction Operational Overview A
Page 18 and 19:
Installation and Set Up 2 Overview
Page 20 and 21:
Installation and Set Up Pre-Install
Page 22 and 23:
Installation and Set Up Installatio
Page 24 and 25: Installation and Set Up Mounting th
Page 32 and 33: Installation and Set Up Installing
Page 38 and 39: Installation and Set Up Connecting
Page 40 and 41: Installation and Set Up Connecting
Page 42 and 43: Installation and Set Up Wiring the
Page 44 and 45: Check Out and Power Up 3 Overview T
Page 46 and 47: Check Out and Power Up Physical Ins
Page 48 and 49: Check Out and Power Up Physical Ins
Page 50 and 51: Check Out and Power Up Operational
Page 52 and 53: Check Out and Power Up Operational
Page 54 and 55: Using the Digital Interfaces Pushbu
Page 56 and 57: Using the Digital Interfaces Displa
Page 68 and 69: Using the Digital Interfaces Hand H
Page 70 and 71: Configuration and Calibration 5 Con
Page 72 and 73: Configuration and Calibration Confi
Page 76 and 77: Configuration and Calibration Calib
Page 78 and 79: Configuration and Calibration Check
Page 80 and 81: Configuration and Calibration Insta
Page 82 and 83: Wiring an SVI II AP Wiring Guidelin
Page 88 and 89: Wiring an SVI II AP HART Physical L
Page 90 and 91: Wiring an SVI II AP Split Range App
Page 98 and 99: HART Communications with Intrinsic
Page 104 and 105: Operation and Maintenance Physical
Page 110 and 111: Operation and Maintenance SVI II AP
Page 112 and 113: Operation and Maintenance SVI II AP
Page 114 and 115: Operation and Maintenance Upgrading
Page 116 and 117: Masoneilan Dresser SVI II AP Instru
Page 124 and 125:
Air Supply Requirements C A high qu
Page 126 and 127:
Advanced Usage E Technology to Maxi
Page 128 and 129:
Advanced Usage Using ValVue 2.4 Dia
Page 130 and 131:
Glossary Closed Compliance Voltage
Page 132 and 133:
Glossary HART Communication The HAR
Page 134 and 135:
Glossary Padj (%) Valves often have
Page 136:
DIRECT SALES OFFICE LOCATIONS BELGI
show all

SVI-II Instruc Man.book - Fagerberg

Create successful ePaper yourself

Delete template?

Save as template?