Hydraulic Design of Highway Culverts - DOT On-Line Publications

More documents

Recommendations

Info

Figure V-12--Performance Curves, Example Problem, 2-36 in CMP Barrels Figure V-13--Topographic map of site 134
Figure V-14--Storage vs. Outflow Relationship 7. Conclusions. Two 900 mm corrugated metal pipes with square edges in a headwall are adequate to satisfy the design conditions. One 900 mm CMP was eliminated due to the routing procedure. The maximum outflow during the design flood is 4.24 m³/s. This creates a headwater elevation of 269.52 m according to the stage versus discharge data. Figure V-15 is a line drawing of the final culvert design. Figure V-15--Selected Culvert Design 135
Page 1:
Publication No. FHWA-NHI-01-020 Sep
Page 4 and 5:
Acknowledgements This document’s
Page 6 and 7:
(Page intentionally blank) iv
Page 8 and 9:
TABLE OF CONTENTS (Cont.) III. CULV
Page 10 and 11:
TABLE OF CONTENTS (Cont.) F. Safety
Page 12 and 13:
LIST OF FIGURES (Cont.) Figure III-
Page 14 and 15:
LIST OF TABLES Table 1. Factors Inf
Page 16 and 17:
ELhf ELhi ELho ELht ELO ELsf ELSO E
Page 18 and 19:
GLOSSARY (Cont.) p Wetted perimeter
Page 20 and 21:
(Page intentionally blank) xviii
Page 22 and 23:
B. Overview of Culverts A culvert i
Page 24 and 25:
Figure I-9--Side-tapered inlet Figu
Page 26 and 27:
. Partly Full (Free Surface) Flow.
Page 28 and 29:
Table 1--Factors Influencing Culver
Page 30 and 31:
D. Economics The hydraulic design o
Page 32 and 33:
For gaged sites, statistical analys
Page 34 and 35:
volume of the remaining runoff hydr
Page 36 and 37:
Figure II-4--Flood hydrograph shape
Page 38 and 39:
Figure II-6--Cross section location
Page 40 and 41:
. Culvert Length. Important dimensi
Page 42 and 43:
HYDROLOGY Peak Flow Check Flows Tab
Page 44 and 45:
Figure III-1--Types of inlet contro
Page 46 and 47:
Figure II-2--Flow contractions for
Page 48 and 49:
The flow transition zone between th
Page 50 and 51:
Figure III-6--Culvert with Inlet Su
Page 52 and 53:
Condition III-7-A represents the cl
Page 54 and 55:
Outlet control flow conditions can
Page 56 and 57:
2 2 Vu Vd HW o + = TW + + HL (6) 2g
Page 58 and 59:
This approximate method works best
Page 60 and 61:
Figure III-12--Weir Crest Length De
Page 62 and 63:
Critical depth is used when the tai
Page 64 and 65:
4. Add the culvert flow and the roa
Page 66 and 67:
NOTE: If the nomographs are put int
Page 68 and 69:
Figure III-19--Critical Depth Chart
Page 70 and 71:
(1) If the Manning’s n value give
Page 72:
Example Problem #1 (SI Units) A cul
Page 80 and 81:
Example Problem #2 (SI Units) A new
Page 82 and 83:
Example Problem #3 (SI Units) Desig
Page 84:
Example Problem #4 (SI Units) An ex
Page 88 and 89:
CHART 51A Figure III-21--Inlet Cont
Page 90 and 91:
2. Outlet Control. a. Partly Full F
Page 92 and 93:
Backwater Calculations From hydraul
Page 95 and 96:
English Units INLET CONTROL: AD 0.
Page 99 and 100:
A. Introduction IV. TAPERED INLETS
Page 101 and 102:
height by more than 10 percent (1.1
Page 103 and 104: A slope-tapered inlet has three pos
Page 105 and 106: The mitered face slope-tapered inle
Page 107 and 108: La is the approximate length of the
Page 109 and 110: E. Design Methods Figure IV-9--Tape
Page 111 and 112: a. Complete Design Data. Fill in th
Page 113 and 114: H 1 i. For FALL < D/4, use side-tap
Page 115: 3. Example Problems a. Example Prob
Page 121 and 122: . Example Problem #1 (English Units
Page 123 and 124: 103
Page 125 and 126: 105
Page 127 and 128: c. Example Problem #2 (SI Units). F
Page 129 and 130: Conclusions: A side-tapered inlet a
Page 131 and 132: 111
Page 133 and 134: G. Circular Pipe Culverts 1. Design
Page 135 and 136: Double barrel slope-tapered inlets
Page 137 and 138: 117
Page 139 and 140: . Example Problem #3 (English Units
Page 141 and 142: 121
Page 143 and 144: A. The Routing Concept V. STORAGE R
Page 145 and 146: C. Application to Culvert Design Fi
Page 147 and 148: Figure V-6--Peak Flow Reduction Bas
Page 149 and 150: I + I + ( 2s / ∆t − O) = ( 2s /
Page 151 and 152: Table 5--Inflow Hydrograph, Example
Page 153: Figure V-10—Culvert Design Form f
Page 157 and 158: Table 5 --Inflow Hydrograph, Exampl
Page 159 and 160: Figure V-18--Culvert Design Form fo
Page 161 and 162: Figure V-22--Storage vs. Outflow Re
Page 163 and 164: A. Introduction VI. SPECIAL CONSIDE
Page 165 and 166: With minor modifications, the culve
Page 167 and 168: If headwater and flow consideration
Page 169 and 170: Figure VI-6--Subatmospheric Pressur
Page 171 and 172: Figure VI-7--Fish Baffles in Culver
Page 173 and 174: A popular method of providing for f
Page 175 and 176: passage of the peak flow. Methods f
Page 177 and 178: Figure VI-15--Sediment Deposition i
Page 179 and 180: 1. Skewed Barrels. The alignment of
Page 181 and 182: Skewed inlets slightly reduce the h
Page 183 and 184: arrel for pipes or the flow per met
Page 185 and 186: Culvert shapes are as important in
Page 187 and 188: • Flood plain ordinances or other
Page 189 and 190: Figure VI-28--Guardrail Adjacent to
Page 191 and 192: Both of the above equations are emp
Page 193 and 194: Tables, charts, and formulas are av
Page 195 and 196: 3. Endwalls and Wingwalls. Culvert
Page 197 and 198: 2. Hydraulic Considerations. Long s
Page 199 and 200: conditions. Variations in the concr
Page 201 and 202: REFERENCES (www.fhwa.dot.gov/bridge
Page 203 and 204: 28. "Design Approaches for Stormwat
Page 205 and 206:
54. "Hydraulic Analysis of Pipe-Arc
Page 207 and 208:
ADDITIONAL REFERENCES (In Alphabeti
Page 209 and 210:
"Risk Analysis For Hydraulic Design
Page 211 and 212:
A. Introduction APPENDIX A DESIGN M
Page 213 and 214:
Chart No. 1 Shape and Material Circ
Page 215 and 216:
NOTE: The rest of this Appendix A i
Page 217 and 218:
Figure A-1--Dimensionless Performan
Page 219 and 220:
developed for circular and elliptic
Page 221 and 222:
APPENDIX B HYDRAULIC RESISTANCE OF
Page 223 and 224:
D. Corrugated Metal Culverts The hy
Page 225 and 226:
Curves are shown for 2-2/3 by 1/2 i
Page 227 and 228:
F. Spiral Rib Pipe Spiral rib pipe
Page 229 and 230:
APPENDIX C CULVERT DESIGN OPTIMIZAT
Page 231 and 232:
C. Inlet Control Performance Curves
Page 233 and 234:
Figure C-4--Optimization of Perform
Page 235 and 236:
E. Tapered Inlet Face Control Perfo
Page 237 and 238:
APPENDIX D DESIGN CHARTS, TABLES, A
Page 239 and 240:
Chart Corrugated Metal Box Culverts
Page 241 and 242:
Chart Circular Tapered Inlets 55A,
Page 243 and 244:
Table 12--Entrance Loss Coefficient
Page 245 and 246:
CHART 1B 225
Page 247 and 248:
227
Page 249 and 250:
229
Page 251 and 252:
231
Page 253 and 254:
233
Page 255 and 256:
235
Page 257 and 258:
237
Page 259 and 260:
239
Page 261 and 262:
241
Page 263 and 264:
243
Page 265 and 266:
245
Page 267 and 268:
247
Page 269 and 270:
249
Page 271 and 272:
251
Page 273 and 274:
253
Page 275 and 276:
255
Page 277 and 278:
257
Page 279 and 280:
259
Page 281 and 282:
261
Page 283 and 284:
263
Page 285 and 286:
265
Page 287 and 288:
267
Page 289 and 290:
269
Page 291 and 292:
271
Page 293 and 294:
273
Page 295 and 296:
275
Page 297 and 298:
277
Page 299 and 300:
279
Page 301 and 302:
281
Page 303 and 304:
283
Page 305 and 306:
285
Page 307 and 308:
287
Page 309 and 310:
289
Page 311 and 312:
291
Page 313 and 314:
293
Page 315 and 316:
295
Page 317 and 318:
297
Page 319 and 320:
299
Page 321 and 322:
301
Page 323 and 324:
303
Page 325 and 326:
305
Page 327 and 328:
307
Page 329 and 330:
309
Page 331 and 332:
311
Page 333 and 334:
313
Page 335 and 336:
315
Page 337 and 338:
317
Page 339 and 340:
319
Page 341 and 342:
321
Page 343 and 344:
323
Page 345 and 346:
325
Page 347 and 348:
327
Page 349 and 350:
329
Page 351 and 352:
331
Page 353 and 354:
333
Page 355 and 356:
335
Page 357 and 358:
337
Page 359 and 360:
339
Page 361 and 362:
341
Page 363 and 364:
343
Page 365 and 366:
345
Page 367 and 368:
347
show all

Hydraulic Design of Highway Culverts - DOT On-Line Publications

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?