CME34M Hardware Manual - RTD Embedded Technologies, Inc.

More documents

Recommendations

Info

Ordering Information The CME34M cpuModule is available with a selection of processors and memory sizes. The cpuModule can also be purchased as part of an Intelligent Data Acquisition Node (IDAN) building block, which consists of the cpuModule and a milled aluminum IDAN frame. The IDAN building block can be used in just about any combination with other IDAN building blocks to create a simple but rugged PC/104 stack. Refer to Appendix C, IDAN Dimensions and Pinout, for more information. The CME34M cpuModule can also be purchased as part of a custom-built RTD HiDAN or HiDANplus High Reliability Intelligent Data Acquisition Node. Contact RTD for more information on its high reliability PC-104 systems. CME34M Model Options The basic cpuModule model options are shown below. Refer to the RTD website (www.rtd.com) for more detailed ordering information and any new variations that may be available. Table 1 CME34M cpuModule Model Options Part Number CME34MVD1860HR-2048 CME34MVD1860HR-1024 CME34MVD1200HR-2048 CME34MVD1200HR-1024 CME34MCS1200HR-2048 CME34MCS1200HR-1024 Description Core 2 Duo (Dual Core) 1.86 GHz, 2GB DDR2-SDRAM Core 2 Duo (Dual Core) 1.86 GHz, 1GB DDR2-SDRAM Core 2 Duo (Dual Core) 1.20 GHz, 2GB DDR2-SDRAM Core 2 Duo (Dual Core) 1.20 GHz, 1GB DDR2-SDRAM Celeron (Single Core) 1.20 GHz, 2GB DDR2-SDRAM Celeron (Single Core) 1.20 GHz, 1GB DDR2-SDRAM Cable Kits and Accessories For maximum flexibility, RTD does not provide cables with the cpuModule. You may wish to purchase the CME34M cpuModule cable kit (P/N XK-CM96), which contains: • Multi-function utility harness (keyboard socket, battery, reset, speaker) • Two serial port cables (DIL-10 to DSUB-9) • VGA monitor cable (DIL-10 to high density 15-pin DSUB) • aDIO cable (DIL-16 to DSUB-25) • Two USB cables (5-pin SIL to USB A) • PCIe/104 Type 2 break-out board (to connect SATA and USB) • Two Ethernet cables (DIL-10 to RJ-45) For additional accessories, refer to the RTD website. 4 CME34M cpuModule BDM-610000076 Rev A
Board Features • Penryn Processor Part Number Speed Cores L2 Cache FSB Speed CME34MVD1860 1.86GHZ Two 6 MB 1066 MHz CME34MVD1200 1.20 GHz Two 3 MB 800 MHz CME34MCS1200 1.20 GHz One 1 MB 800 MHz – Intel 64 architecture for 64-bit processing. – Enhanced Intel SpeedStep Technology and dynamic FSB frequency switching (Core 2 Duo only). – Enhanced Intel Dynamic Acceleration Technology and Enhanced Multi-Threaded Thermal Management (Core 2 Duo only) – Supports enhanced Intel Virtualization Technology (Core 2 Duo only) – 45 nm process • 1 GB or 2GBytes BGA DDR2 SDRAM – Dual-channel memory interface – Up to 800MHz Data Rate per channel – Surface Mounted for maximum reliability • Stackable 156-pin PCIe/104 Type 2 bus on top – Four PCI Express x1 Lanes – Two PCI Express x4 Lanes – Two SATA 2.0 – Two USB 2.0 – SMBus • Stackable 156-pin PCIe/104 Type 2 bus on bottom – Four PCI Express x1 Lanes – Two PCI Express x4 Lanes – One SATA 2.0 – Two USB 2.0 – SMBus • Advanced Thermal Management – Thermal Monitor throttles processor and memory to prevent thermal runaway – Auto Fan Control only runs fan when needed – SMBus Temperature Monitor for CPU and board temperature – Mini Fan Heatsink with Auto Fan control – Passive Structural Heatsink & Heatpipes in IDAN and HiDAN System Configurations • Advanced Programmable Interrupt Controller (APIC) – 24 interrupt channels with APIC enabled (15 in legacy PIC mode) – High Precision Event Timer • Advanced Configuration and Power Interface (ACPI) – ACPI 3.0 Compliant BDM-610000076 Rev A Chapter 1: Introduction 5
Page 1 and 2: CME34M cpuModules User’s Manual B
Page 3 and 4: CME34M cpuModules www.rtd.com ISO90
Page 5 and 6: Chapter 1 Introduction Table of Con
Page 7 and 8: Wake-on-aDIO . . . . . . . . . . .
Page 9 and 10: Chapter 1 Introduction This manual
Page 11: Enhanced Intel SpeedStep (Core 2 Du
Page 15 and 16: - Match Mode Interrupt generates an
Page 17 and 18: Specifications Physical Characteris
Page 19 and 20: Table 4 Electrical Characteristics
Page 21 and 22: Chapter 2 Getting Started For many
Page 23 and 24: Table 5 CME34M Basic Connectors Con
Page 25 and 26: Stack Example The figure below show
Page 27 and 28: Connecting the Utility Cable The mu
Page 29 and 30: Chapter 3 Connecting the cpuModule
Page 31 and 32: Table 6 CME34M Basic Connectors Con
Page 33 and 34: Utility Port Connector (CN5) The ut
Page 35 and 36: Battery Pin 9 of the multi-function
Page 37 and 38: SATA Disk Chip Socket (U6) The SATA
Page 39 and 40: Facing the serial port’s connecto
Page 41 and 42: Dual Serial Port Modes The serial p
Page 43 and 44: Advanced Digital I/O (aDIO) Port (C
Page 45 and 46: Ethernet (10/100/1000Base-T and -TX
Page 47 and 48: Table 26 PCIe/104 Type 2 Bus Signal
Page 49 and 50: PCIe Link Configuration This cpuMod
Page 51 and 52: Chapter 4 Using the cpuModule This
Page 53 and 54: Main Menu Setup Fields The followin
Page 55 and 56: I/O Address Map As with all standar
Page 57 and 58: Non-Standard Serial Port Modes It i
Page 59 and 60: Table 45 DIO-Control I/O Address 9C
Page 61 and 62: Figure 6 aDIO Match Mode Strobe Mod
Page 63 and 64:
Table 50 Real Time Clock Registers
Page 65 and 66:
Thermal Management The cpuModule ha
Page 67 and 68:
• Resume on RTC Alarm: The RTC Al
Page 69 and 70:
Reset Status Register The cpuModule
Page 71 and 72:
Features and Settings That Can Affe
Page 73 and 74:
Appendix A Hardware Reference This
Page 75 and 76:
Figure 9 CME34M Jumper Locations (t
Page 77 and 78:
Physical Dimensions Figure 10 shows
Page 79 and 80:
Appendix B Troubleshooting Many pro
Page 81 and 82:
Table 66 Troubleshooting (cont’d)
Page 83 and 84:
Appendix C IDAN Dimensions and Pino
Page 85 and 86:
External I/O Connections Table 67 P
Page 87 and 88:
BDM-610000076 Rev A Appendix C: IDA
Page 89 and 90:
Table 72 USB — 9-Pin D Connector
Page 91 and 92:
Appendix D Additional Information A
Page 93 and 94:
Appendix E Limited Warranty RTD Emb
show all

CME34M Hardware Manual - RTD Embedded Technologies, Inc.

Create successful ePaper yourself

Delete template?

Save as template?