M800 Gas Flow Computer - Spirax Sarco

More documents

Recommendations

Info

6.6.2 Pressure sensor menu This menu configures the pressure transmitter or allows a nominal line pressure to be entered. P min is the pressure when the transmitter outputs 4 mA and P max is the pressure when the transmitter outputs 20 mA. Commissioning mode • Inputs • Pres Commissioning mode • Inputs • Pres Yes ok Commissioning mode • Inputs • Pres • P Min Enter pressure (bar g or psi g) Commissioning mode • Inputs • Pres ok • P Min 0.00 Enter pressure (bar g or psi g) Commissioning mode • Inputs • Pres No Commissioning mode • Inputs • Pres • P Max Commissioning mode • Inputs • Pres • P Max 3.00 ok ok Enter pressure (bar g or psi g) Commissioning mode • Inputs • Pres • P nom Commissioning mode • Inputs • Pres • P nom 3.00 ok After the data has been entered, exit the inputs sub-menu by pressing . The menu will then step to outputs (see section 6.7) 48 IM-P333-25 MI Issue 2
6.7 Outputs The Outputs sub-menu allows the <strong>M800</strong>'s outputs to be configured. The <strong>M800</strong> operates on a 'plug and play' principle and hence will only show the configuration menus for the selected options, i.e. if no additional 4-20 mA outputs are purchased the menu will only show the configuration menu for the flow 4-20 mA. Commissioning mode • Outputs Commissioning mode • Outputs • 4-20 mA 4-20 mA output menu See Section 6.7.1 and 6.7.2 Commissioning mode • Outputs • Pulse Pulse output menu See Section 6.7.3 Commissioning mode • Outputs • Comms Comms output menu See Section 6.7.4 IM-P333-25 MI Issue 2 49
Page 1 and 2: 3330951/ 2 IM-P333-25 MI Issue 2 M8
Page 3 and 4: The symbols, used on the product an
Page 5 and 6: 1.11 Permits to work All work must
Page 7 and 8: 3. System overview 3.1 Orifice plat
Page 9 and 10: 3.3 Gilflo ILVA mechanical installa
Page 11 and 12: 3.5 4 - 20 mA linear device mechani
Page 13 and 14: 4.1 Wall mounted version h Fig. 7 F
Page 15 and 16: h b Fig. 12 a h c 3. Unclip the hi
Page 17 and 18: Fitting of option boards 1. Isolate
Page 19 and 20: 5.2 Important - Please read the fol
Page 21 and 22: 5.4 Wiring diagram - Vortex flowmet
Page 23 and 24: 5.6 Wiring diagram - Pulsed output
Page 25 and 26: RS485 option board Additional notes
Page 27 and 28: Master 1200 m (4000 ft) -Tx Tx T Rt
Page 29 and 30: Run mode data sequence 20290 Nm³
Page 31 and 32: 6.3 Commissioning mode The commissi
Page 33 and 34: Continued from page 32 Commissionin
Page 35 and 36: Commissioning mode • Basic Data C
Page 37 and 38: 6.5.1 Commissioning sequence for th
Page 41 and 42: To page 40 Continued from page 40 C
Page 43 and 44: Table 2 Specific gas dynamic viscos
Page 47: 6.6.1 Temperature sensor menu. The
Page 51 and 52: Commissioning mode • Outputs •
Page 53 and 54: 6.7.2.1 Optional 4-20 mA temperatur
Page 55 and 56: 6.7.3 Pulse output This sub-menu al
Page 57 and 58: Summary of the Modbus Protocol for
Page 59 and 60: 6.8 Test menu The test sub-menu all
Page 61 and 62: 6.8.3 Testing the 4-20 mA outputs T
Page 63 and 64: Continued from page 62 Commissionin
Page 65 and 66: 6.12 Clock This allows the time and
Page 67 and 68: To page 66 Continued from page 66
Page 69 and 70: 7. Fault finding WARNING: Before co
Page 71 and 72: Commissioning Error messages Error
Page 73 and 74: 8. Maintenance Note: Before actioni
Page 75 and 76: 9.7 Input technical data 4-20 mA in
Page 77 and 78: 9.10 Maximum and minimum programmab
Page 79 and 80: IM-P333-25 MI Issue 2 79

M800 Gas Flow Computer - Spirax Sarco

Create successful ePaper yourself

Delete template?

Save as template?