M800 Gas Flow Computer - Spirax Sarco

More documents

Recommendations

Info

6.8.1 Display test This allows the display to be tested. Pressing the right button will cause all the segments on the display to be turned on. Pressing the left button cancels the test and steps to the next stage. Commissioning mode • Test Commissioning mode • Test • Display Commissioning mode • Test • Display 6.8.2 Testing the 4-20 mA Inputs This allows the 4-20 mA input from the sensors to be displayed. The 4-20 mA input can be displayed for the flow, pressure and temperature. Commissioning mode • Test • Inputs Commissioning mode • Test • Inputs • Flow Commissioning mode • Test • Inputs • Flow 13.345 mA Note: If a linear input type flowmeter is selected these menus do not appear. Commissioning mode • Test • Inputs • Temp Commissioning mode • Test • Inputs • Pres Commissioning mode • Test • Inputs • Flow 11.403 mA Commissioning mode • Test • Inputs • Flow 10.192 mA 60 IM-P333-25 MI Issue 2
6.8.3 Testing the 4-20 mA outputs This allows the 4-20 mA outputs to be tested. Editing the value and pressing the 'OK' button can set the output to the selected current output. This current will continue to be transmitted for ten minutes unless the cancel option is chosen. The 4-20 mA output can be set for the flow, pressure and temperature depending on the options fitted. Commissioning mode • Test • 4-20 mA out Commissioning mode • Test • 4-20 mA out • Flow Commissioning mode • Test • 4-20 mA out • Flow 04.00 mA ok Note: If a linear input type flowmeter is selected or no 4-20 mA option board is fitted then these menus do not appear. Commissioning mode • Test • 4-20 mA out • Temp Commissioning mode • Test • 4-20 mA out • Pres Commissioning mode • Test • 4-20 mA out • Temp 04.00 mA Commissioning mode • Test • 4-20 mA out • Pres 04.00 mA ok ok After the data has been entered, exit the 4-20 mA output test by pressing . The menu will then step to Testing the pulse output (see Section 6.8.4). 6.8.4 Testing the Pulse output This allows the pulsed output to be tested. By selecting 'ON' or 'OFF' the desired test state of the pulsed output can be selected. Once the 'OK' button is pressed the pulsed output will remain in the selected state for ten minutes or until the cancel option is chosen. Commissioning mode • Test • Pulse Out Commissioning mode • Test • Pulse Out On ok Commissioning mode • Test • Pulse Out Off ok IM-P333-25 MI Issue 2 61
Page 1 and 2:
3330951/ 2 IM-P333-25 MI Issue 2 M8
Page 3 and 4:
The symbols, used on the product an
Page 5 and 6:
1.11 Permits to work All work must
Page 7 and 8:
3. System overview 3.1 Orifice plat
Page 9 and 10: 3.3 Gilflo ILVA mechanical installa
Page 11 and 12: 3.5 4 - 20 mA linear device mechani
Page 13 and 14: 4.1 Wall mounted version h Fig. 7 F
Page 15 and 16: h b Fig. 12 a h c 3. Unclip the hi
Page 17 and 18: Fitting of option boards 1. Isolate
Page 19 and 20: 5.2 Important - Please read the fol
Page 21 and 22: 5.4 Wiring diagram - Vortex flowmet
Page 23 and 24: 5.6 Wiring diagram - Pulsed output
Page 25 and 26: RS485 option board Additional notes
Page 27 and 28: Master 1200 m (4000 ft) -Tx Tx T Rt
Page 29 and 30: Run mode data sequence 20290 Nm³
Page 31 and 32: 6.3 Commissioning mode The commissi
Page 33 and 34: Continued from page 32 Commissionin
Page 35 and 36: Commissioning mode • Basic Data C
Page 37 and 38: 6.5.1 Commissioning sequence for th
Page 41 and 42: To page 40 Continued from page 40 C
Page 43 and 44: Table 2 Specific gas dynamic viscos
Page 47 and 48: 6.6.1 Temperature sensor menu. The
Page 49 and 50: 6.7 Outputs The Outputs sub-menu al
Page 51 and 52: Commissioning mode • Outputs •
Page 53 and 54: 6.7.2.1 Optional 4-20 mA temperatur
Page 55 and 56: 6.7.3 Pulse output This sub-menu al
Page 57 and 58: Summary of the Modbus Protocol for
Page 59: 6.8 Test menu The test sub-menu all
Page 63 and 64: Continued from page 62 Commissionin
Page 65 and 66: 6.12 Clock This allows the time and
Page 67 and 68: To page 66 Continued from page 66
Page 69 and 70: 7. Fault finding WARNING: Before co
Page 71 and 72: Commissioning Error messages Error
Page 73 and 74: 8. Maintenance Note: Before actioni
Page 75 and 76: 9.7 Input technical data 4-20 mA in
Page 77 and 78: 9.10 Maximum and minimum programmab
Page 79 and 80: IM-P333-25 MI Issue 2 79
show all

M800 Gas Flow Computer - Spirax Sarco

Create successful ePaper yourself

Delete template?

Save as template?