M800 Gas Flow Computer - Spirax Sarco

More documents

Recommendations

Info

6.10 Software version This allows the software version to be viewed. Commissioning mode • SW version Commissioning mode • SW version 0.01 6.11 Set password This allows the default pass code to be changed to a user defined value. Commissioning mode • Set pass Commissioning mode • Set pass ok It is important that if the default pass code is changed that the new value is noted and kept safe. 64 IM-P333-25 MI Issue 2
6.12 Clock This allows the time and date to be set. The time is entered in the 24 hr format. The Format menu sets the date as either Day/Month or Month/Day. Commissioning mode • Set clock Commissioning mode • Set clock • Hrs (24) Commissioning mode • Set clock • Hrs (24) ok 14 Commissioning mode • Set clock • Mins Commissioning mode • Set clock • Mins ok 34 Commissioning mode • Set clock • Year Commissioning mode • Set clock • Year ok 06 Commissioning mode • Set clock • Month Commissioning mode • Set clock • Month ok 05 Commissioning mode • Set clock • Day Commissioning mode • Set clock • Day ok 17 Commissioning mode • Set clock • Format Commissioning mode • Set clock • Format ok d/m Commissioning mode • Set clock • Format ok m/d After the data has been entered, exit the set clock menu by pressing . The menu will then step to the Timers menu (see Section 6.13). IM-P333-25 MI Issue 2 65
Page 1 and 2:
3330951/ 2 IM-P333-25 MI Issue 2 M8
Page 3 and 4:
The symbols, used on the product an
Page 5 and 6:
1.11 Permits to work All work must
Page 7 and 8:
3. System overview 3.1 Orifice plat
Page 9 and 10:
3.3 Gilflo ILVA mechanical installa
Page 11 and 12:
3.5 4 - 20 mA linear device mechani
Page 13 and 14: 4.1 Wall mounted version h Fig. 7 F
Page 15 and 16: h b Fig. 12 a h c 3. Unclip the hi
Page 17 and 18: Fitting of option boards 1. Isolate
Page 19 and 20: 5.2 Important - Please read the fol
Page 21 and 22: 5.4 Wiring diagram - Vortex flowmet
Page 23 and 24: 5.6 Wiring diagram - Pulsed output
Page 25 and 26: RS485 option board Additional notes
Page 27 and 28: Master 1200 m (4000 ft) -Tx Tx T Rt
Page 29 and 30: Run mode data sequence 20290 Nm³
Page 31 and 32: 6.3 Commissioning mode The commissi
Page 33 and 34: Continued from page 32 Commissionin
Page 35 and 36: Commissioning mode • Basic Data C
Page 37 and 38: 6.5.1 Commissioning sequence for th
Page 41 and 42: To page 40 Continued from page 40 C
Page 43 and 44: Table 2 Specific gas dynamic viscos
Page 47 and 48: 6.6.1 Temperature sensor menu. The
Page 49 and 50: 6.7 Outputs The Outputs sub-menu al
Page 51 and 52: Commissioning mode • Outputs •
Page 53 and 54: 6.7.2.1 Optional 4-20 mA temperatur
Page 55 and 56: 6.7.3 Pulse output This sub-menu al
Page 57 and 58: Summary of the Modbus Protocol for
Page 59 and 60: 6.8 Test menu The test sub-menu all
Page 61 and 62: 6.8.3 Testing the 4-20 mA outputs T
Page 63: Continued from page 62 Commissionin
Page 67 and 68: To page 66 Continued from page 66
Page 69 and 70: 7. Fault finding WARNING: Before co
Page 71 and 72: Commissioning Error messages Error
Page 73 and 74: 8. Maintenance Note: Before actioni
Page 75 and 76: 9.7 Input technical data 4-20 mA in
Page 77 and 78: 9.10 Maximum and minimum programmab
Page 79 and 80: IM-P333-25 MI Issue 2 79
show all

M800 Gas Flow Computer - Spirax Sarco

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?